User manual HOBBYKING HK-7X

[. . . ] Incorrect installation and operation will result in severe property loss and personal injuries. HK-7X 2. 4GHz control system is exclusively designed for civil use of R/C models. Don't use it in any other flying machines. The governmence for R/C model is different in different place, therefore, please consult your local regulatory body and follow the rules and regulations to operate legally. [. . . ] 4) Release the 'BIND button' of transmitter, the RF LED will keep light, which indicates it is in working mode. on 4 1. Mounting of Receiver Installation position shall follow these conditions: 1. Keep the receiver away from engine, motor, ESC, battery, and other metal parts. 2. The antenna can not be covered by metal, carbon material or the other electronic conduction material. Keep the antenna in 90 degrees with installed frame or bottom plate, it means that try to keep the antenna visible, see the graph below: The receiver has been plugged bind line Bind button on the back of transmitter Bind button of transmitter Notice: 1)HK-7X 2. 4GHz remote controller system sustain multiple receivers operation and long-distance scaning, so please make sure there's only your radio scaning. If there is any person who also use HK-7X 2. 4GHz remote controller system at local, please operate only after other users pare the signal. HK-7X supports seven models saving in one transmitter, they are numbering as n1 to n7. The binding will save the serial number in receiver. So if you bind one receiver with n1, it can only work when the transmitter is switched to n1. 2. Connect Devices to Receiver Connecting all devices and parts to the corresponding channels. Take notice of 3P signal wire must be connected in right way, or it will cause the severe damage to certain device or fail to work. There are some corresponding symbols of 3P on one side of the receiver: (-) means cathode of power connected to the earth, usually links to the black line or brown line of 3P signal wire (+) means the anode of power, usually links to the red wire of 3P singal wires. (s) means signal wire, usually links to the white or yellow wire of 3P singal wires. Notice:please assess the power demand of the receiver of model when selecting the electricity supply style, ensure the receiver can get enough power supply when using, the voltage of the receiver not less than 4. 2V at any time. 4. Control Distance All remote equipment has an effective range. It's not the same on the ground, and on the water surface or in the sky; It's not the same on flat ground and complex land; It's not the same in rainy days and in sunny days; And besides, the external electrical environment is changing continuously. It's quite necessary for the users who want to control at a long distance to test effective distance beforehand. Radio wave transfers almost in a straight line, please make sure there is no object between antenna and the controlled model. And the antenna should point at receiver's antenna, and keep the controlled model in certain distance where the model can be seen. controller system 3. Binding Transmitter and Receiver Before using the 2. 4GHz remote controller system, you must bind the transmitter and the receiver. Binding them as following steps: 1) Power on receiver by plugging the ESC line, then plug the 'BIND line' into the 'BIND' slot of receiver. Then the LED of receiver will flash three times per second. Then you can remove the "BIND" line'. 5 Part2 Transmitter Manual 1 Features 1LED display which shows model type and battery voltage on normal status. 3Support 5 points throttle(THR) curve in NORMAL mode and IDLE mode. 4Support 5 points pitch(PIT) curve in NORMAL mode, IDLE mode and HOLD mode. 5Support HELI(helicopter) mode and AERO mode. Following modes are supported in each mode: 6 7 8 9 10 11 12 13 14 7 channels standard servo signal output. [. . . ] If the throttle stick not is in the lowest position when power on, the transmitter will block in warning status. You will see "THro" in panel and hear continuously beep till you move the stick to the lowest position. 15 Using PPM signal HK-7X 7CH is a digital device, it also has a signal output slot on the bottom. But in common using, the output signal is PCM format. If you are using a flying simulator on your computer, the simulator software can not work with HK-7X PCM signal. [. . . ]