User manual HOMELITE UT10532 OPERATORS MANUAL

[. . . ] 33cc CHAIN SAW UT10532 Your chain saw has been engineered and manufactured to Homelite's high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Thank you for buying a Homelite product. SAVE THIS MANUAL FOR FUTURE REFERENCE TABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 General Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Follow the correct tree felling procedure as stated in Proper Procedure For Tree Felling after you have removed the large buttress roots. WEDGE Fig. Bucking is the term used for cutting a fallen tree to the desired log length. Support small logs on a saw horse or another log while bucking. Make sure that no objects can contact the guide bar nose and chain during cutting, this can cause kickback. To avoid the danger, keep the SAFE-T-TIP anti-kickback device attached while cutting. Refer to Kickback in the Specific Safety Rules section of this manual for more information. During bucking operations, stand on the uphill side so that the cut-off section of the log cannot roll over you. Sometimes it is impossible to avoid pinching (with just standard cutting techniques) or difficult to predict which way a log will settle when cut. VERTICAL CUT LOOSE SECTION HORIZONTAL CUT Fig. 26 Page 18 OPERATION BUCKING WITH A WEDGE See Figure 27. If the wood diameter is large enough for you to insert a soft bucking wedge without touching the chain, you should use the wedge to hold the cut open to prevent pinching. NOTE: When bucking or felling with a wedge, you may need to remove the SAFE-T-TIP anti-kickback device to allow the bar to be drawn through the cut. After you complete the cut, reinstall the tip. WEDGE BUCKING LOGS UNDER STRESS See Figure 28. Make the first bucking cut 1/3 of the way through the log and finish with a 2/3 cut on the opposite side. As you cut the log, it will tend to bend. The saw can become pinched or hung in the log if you make the first cut deeper than 1/3 of the diameter of the log. Give special attention to logs under stress to prevent the bar and chain from pinching. Fig. 27 LOG SUPPORTED AT ONE END FINISHING CUT LOAD OVERBUCKING See Figure 29. Begin on the top side of the log with the bottom of the saw against the log; exert light pressure downward. Note that the saw will tend to pull away from you. 1ST CUT 1/3 DIA LOG SUPPORTED AT BOTH ENDS 1ST CUT 1/3 DIA LOAD FINISHING CUT Fig. 29 Page 19 OPERATION UNDERBUCKING See Figure 30. Begin on the under side of the log with the top of the saw against the log; exert light pressure upward. During underbucking, the saw will tend to push back at you. [. . . ] warrants to the ultimate purchaser and each subsequent purchaser that your nonroad or small off-road engine will be designed, built, and equipped, at the time of sale, to meet all applicable regulations. also warrants to the initial purchaser and each subsequent purchaser that your nonroad or small off-road engine is free from defects in materials and workmanship which cause the engine to fail to conform with applicable regulations for a period of two years. The 1995 and later small off road engines are warranted for two years in California. In all other states for 1997 and later model years, EPA requires manufacturers to warrant non-road engines for two years. [. . . ]