User manual HONEYWELL HS 20

[. . . ] This process is called the "Teach-in". The Hometronic Manager and the new components exchange data during the procedure. The socket switching module has a radio receiver whose function can be impaired by metallic objects! When selecting the operating site ensure that there is sufficient distance to metallic objects, such as steel reinforcements, metallic wallpaper, etc. [. . . ] Uninstalling collection relay Change to the "Settings" submenu (refer to Page 7). Turn the Dial button until "De- HEATING/COOLING SHUTTERS Installation" is selected. SENSOR The following text is displayed: Turn the Dial button to the left until "Boiler request" is selected. SENSOR SETPOINT ADJUSTER ROOM CONTROL BOILER REQUEST 10 Teach-in Press the Dial button. The following text is displayed: SWITCHING MODULE ANTI-FREEZE SENSOR THERMOSTAT SWITCHING MODULE ANTI-FREEZE SENSOR THERMOSTAT SWITCHING MODULE ANTI-FREEZE SENSOR THERMOSTAT * * * * Turn the Dial button to the left until "Thermostat" is selected. Press the Dial button. The "*" after the "Thermostat" entry disappears. The collection relay is uninstalled. Successful Teach-in The Teach-in has been completed successfully when the flashing LED at the switching module extinguishes. A Teach-in only has to be carried out successfully once. If the socket switching module is plugged into another socket or if the power fails, no new Teach-in is required. Note: The plugged-in device is always switched off after it has been plugged in again or after the power supply has returned. 11 Teach-in Failed Teach-in The Teach-in has failed when the LED at the switching module flashes green with short interruptions. The data transfer per radio did not take place or was faulty. Note: Since the socket switching module tries to establish a connection to the Hometronic Manager for the duration of 4 minutes, a failed Teach-in is not displayed by the LED until after the 4 minutes have passed. Carry out the following measures after a Teach-in has failed: ­ Improve the data transfer ­ Repeat the Teach-in Remove/avoid disturbing shielding devices, e. g. : ­ ­ ­ ­ ­ ­ Greater distance to a neighboring socket switching module Wireless headphones Garage door opener Remote controls Disturbing objects in the vicinity Metal parts 12 Teach-in Repeating the Teach-in Press the Dial button in order to activate the Teach-in mode. MODULE-1 MODULE-2 MODULE-3 MODULE-4 The module is activated again for teaching-in. * 13 Operation Operation Exceeding the maximum connected load* can destroy the switching module. Caution! Fuse the switching module with a maximum of 16 A. Insert the device into the socket switching module. Operating the socket switching module manually In order to switch plugged-in devices on or off, press briefly on the button of the socket switching module. The switching state is displayed by the built-in LED. · LED on = Device on · LED off = Device off Controlling the socket Hometronic Manager switching module with the Various operating modes of the socket switching module are possible with the Hometronic. You can use the "Presence simulation" function for example to repeat the operation course of the last 7 days. With the "automatic brightness control" function, lamps or devices are controlled via the brightness of an installed sun module HB 05/HB 15. However, this operating mode only makes sense if, e. g. a lamp, radio or similar devices are connected to the switching device. For further information please read in the "Operation" chapter in the Hometronic Manager instructions. [. . . ] connected load at Ambient temperature 30 °C Approx. 3680 W, (230 VAC/16 A) Ambient temperature > 30 °C Approx. 2000 W, (230 VAC/8. 7 A) 17 Appendix Information to the customer After the Teach-in has been completed (in this case of the socket switching module) the customer can be informed via the Hometronic System: Familiarize the customer with the basic operation of the Hometronic Manager. Explain the operation of the components on site. [. . . ]