User manual HONEYWELL M6410C

[. . . ] The M6410C/L and M7410C actuators are also compatible with any controller providing intelligent position control and having a built-in shut-off function. These actuators are well suited for applications where space is limited and minimum power consumption is required. The actuators are both attractive and robust in design. 24 Vac +10%/-30%; 50/60 Hz 230 Vac +10%/-30%; 50/60 Hz Power consumption 0. 7 VA (24-V models) 7. 0 VA (230-V models) Control mode floating Stroke 6. 5 mm Running time 150 s at 50 Hz, 125 s at 60 Hz Stem force version-dependent (see Table 1) Protection standard IP 43 as per EN60529 Insulation class II/III, depending on type (as per EN 60730) Connection cables 1. 5 m Ambient operating limits 0. . . 60 °C Medium valve temp. 120 °C Weight 0. 4 kg Suitable valves see Table 1 Manual operation see Table 1 The controller output stage must be suitable for current peaks of up to 800 volts. [. . . ] 100 mA 24. . . 230 Vac, max 3 (1) A S1 (fixed): 17. 8 ± 0. 2 mm S2 (adjustable): 11. 7 ± 0. 2 mm EN0B-0096GE51 R0909 Auxiliary Switches Ratings Switch position (factory-supplied) ® U. S. Registered Trademark Copyright © 2009 Honeywell Inc. · All rights reserved M6410C/L, M7410C Small 3-Position Linear Valve Actuators OPERATION The movement of the electric actuators is produced by a screw spindle which is driven in both directions by a synchronous motor through a set of gears. A magnetic clutch limits the torque of the gear assembly and the driving force of the actuators. The actuators are fixed to the valve body by means of a coupling ring requiring no tools for mounting. The actuators are maintenance-free and supplied completely with a ready-to-wire connecting cable. Table 1. Versions version standard power supply 24 Vac 24 Vac 24 Vac 24 Vac 230 Vac 230 Vac 24 Vac 24 Vac 230 Vac 230 Vac manual operation provided by valve adj. cap stem force 180 N 300 N 180 N 300 N 180 N 300 N 180 N 300 N 180 N 300 N aux. switch S1 S2 ------------X X X X X X X X housing type A B C C C C C C C C OS number M7410C1007 M7410C1015 M6410C2023 M6410C2031 M6410L2023 M6410L2031 M6410C4029 M6410C4037 M6410L4029 M6410L4037 with manual operation integrated with manual operation and aux. Below the skin, the adjustment screw can be accessed. Turn the screw clockwise until the end stop is reached. Turn the screw counterclockwise until the switch point is achieved. To check that the required position has been set, move the actuator. Finally, seal the adjustment hole with a piece of tape. B B closing opening A AB A AB B B Fig. Electric wiring of motor MANUAL OPERATION The actuators with integrated manual operation (see Table 1) feature a hexagonal key hole for manual operation. For more comfort, an additional knob for manual adjustment is packed separately. To avoid damaging the valve, separate the actuator from the power supply before adjusting manually. Fig. Adjustment of auxiliary switch S2 Electric Wiring of Auxiliary Switches 4 mm The electrical installation must comply with the wiring diagram shown in Fig. [. . . ] Adjustment of auxiliary switch S2 Electric Wiring of Auxiliary Switches 4 mm The electrical installation must comply with the wiring diagram shown in Fig. If the auxiliary switch is connected to 230 Vac, a switch with a contact gap of at least 3 mm for each pole must be fitted with the installation. Fig. Manual operation 3 EN0B-0096GE51 R0909 M6410C/L, M7410C Small 3-Position Linear Valve Actuators (230 Vac, only): 24 Vac: max. 5 (1) A M6410C/L M7410E All Other Valves DN 15 - DN 40 DN 15 - DN 20 DN 25 - DN 40 DN15 DN20 DN25 DN40 open A B A B A B close close A B A B A B open E. [. . . ]