User manual HONEYWELL NXS

[. . . ] AT LEAST THE 10 FOLLOWING STEPS OF THE START-UP QUICK GUIDE MUST BE PERFORMED DURING THE INSTALLATION AND COMMISSIONING. IF ANY PROBLEMS OCCUR, PLEASE CONTACT YOUR LOCAL DISTRIBUTOR. Start-up Quick Guide 1. Check that the delivery corresponds to your order, see Chapter 1. Before taking any commissioning actions read carefully the safety instructions in Chapter 1. [. . . ] Through the menus, you can also adjust the contrast of the display (page 90). RUN READY Local Location Description Number of items available; Item value Monitor V1 V14 The first menu level consists of menus M1 to M7 and is called the Main menu. The user can navigate in the main menu using the Browser buttons up and down. The desired submenu can be entered from the main menu using the Menu buttons. When there still are pages to enter under the currently displayed menu or page, you can see an arrow ( ) in the lower right corner of the display and by pressing the Menu button right, you can reach the next menu level. The control keypad navigation chart is shown on the next page. Please note that the menu M1 is located in the lower left corner. From there you will be able to navigate your way up to the desired menu using the menu and browser buttons. More detailed descriptions of the menus you will find later in this Chapter. 7 70(102) CONTROL KEYPAD READY I/Oterm I/Ote rm R EADY I/Oterm R EADY Expander boards G1 G5 A:NXOPTA1 Parameters G1 G1 P1 P3 STOP I/Ote rm R EADY I/Ote rm STOP R EADY System Menu Language enter Change value S1 S9 English Browse READY I/Ote rm I/Ote rm READY I/Oterm READY Fault history H1 H3 11 Output phase Operation days T1 T7 17 STOP I/Ote rm FAULT I/Ote rm STOP FAULT I/Ote rm STOP FAULT Active faults or: 11 Output phase Operation days F0 F T1 T7 17 ST OP I/Ote rm R EADY I/Ote rm ST OP R EADY Keypad control Control Place enter P1 P3 I/O Terminal Browse Change value R EADY I/Ote rm I/Ote rm R EADY L oc al READY Parameters Basic parameters G1 G9 P1 P15 Min Frequency enter 13. 95 Hz Browse Change value RU N I/Ote rm R EADY RUN I/Oterm READY Monitor Output frequency V1 V15 13. 95 Hz No editing! Figure 7-3. Keypad navigation chart CONTROL KEYPAD 7. 3. 1 Monitoring menu (M1) 71(102) 7 You can enter the Monitoring menu from the Main menu by pushing the Menu button right when the location indication M1 is visible on the first line of the display. How to browse through the monitored values is presented in Figure 7-4. The monitored signals carry the indication V#. # and they are listed in Table 7-1. The values are updated once every 0. 3 seconds. This menu is meant only for signal checking. For changing values of parameters see Chapter 7. 3. 2. RUN Lo ca l R EADY FreqReference 13. 95 Hz RUN Local READY RUN Local READY Monitor Output frequency V1 V14 Figure 7-4. Monitoring menu Code V1. 1 V1. 2 V1. 3 V1. 4 V1. 5 V1. 6 V1. 7 V1. 8 V1. 9 V1. 10 V1. 11 V1. 12 V1. 13 V1. 14 V1. 15 V1. 16 M1. 17 Signal name Output frequency Frequency reference Motor speed Motor current Motor torque Motor power Motor voltage DC-link voltage Unit temperature Motor temperature Voltage input Current input DIN1, DIN2, DIN3 DIN4, DIN5, DIN6 DO1, RO1, RO2 Analogue output current Multimonitoring items Unit Hz Hz rpm A % % V V ºC % V mA 13. 95 Hz Description Frequency to the motor Calculated motor speed Measured motor current Calculated motor shaft torque Calculated motor shaft power Calculated motor voltage Measured DC-link voltage Heat sink temperature Calculated motor temperature. AI1 AI2 Digital input statuses Digital input statuses Digital and relay output statuses AO1 Displays three selectable monitoring values. See chapter 7. 3. 6. 5. mA Table 7-1. Monitored signals Note: The All in One applications embody more monitoring values. 7 72(102) 7. 3. 2 Parameter menu (M2) CONTROL KEYPAD Parameters are the way of conveying the commands of the user to the frequency converter. The parameter values can be edited by entering the Parameter Menu from the Main Menu when the location indication M2 is visible on the first line of the display. The value editing procedure is presented in Figure 7-5. Push the Menu button right once to move into the Parameter Group Menu (G#). Locate the parameter group desired by using the Browser buttons and push the Menu button right again to enter the group and its parameters. [. . . ] If no motor overload exists, check the temperature model parameters. Reset the fault and restart. Should the fault re-occur, contact the distributor near to you. Check motor cooling and loading Check thermistor connection (If thermistor input of the option board is not in use it has to be short circuited) Check loading. Contact the distributor near to you. 26 29 Start-up prevented Thermistor fault 31 IGBT temperature (hardware) Fan cooling 32 34 35 CAN bus communication Application 36 Control unit NXS Control Unit can not control NXP Power Unit and vice versa Ensure that there is another device on the bus with the same configuration. [. . . ]