User manual HONEYWELL TH4000

[. . . ] Heat: Thermostat controls only the heating system. Off: Heating and cooling systems are off. PRO TH4000 Programmable Thermostat Quick reference to display screen Low battery warning (see page 15) Current inside temperature Replace Batt Inside Set To Current day/time (see page 6) Temperature setting (see pages 11-13) Current program period Wake/Leave/Return/Sleep (see pages 10-11) 75 Wake ° 6:30 75 AM ° System status Heat On/Cool On (If flashing, see page 14) Wed Cool On 5 Operating Manual Set the time and day Press SET, then adjust time Set Clock 6:30 Press SET, AM 1 Press the SET button, then press or to set the clock time. 2 Press the SET button, then press or to select the day of the week. 3 Press RUN to save & exit. Note: If the display flashes Set Clock, the thermostat will follow your settings for the weekday "Wake" time period until you reset the time and day. then select current day Set Day Wed 6 PRO TH4000 Programmable Thermostat System switch The SYSTEM switch can be set to control your heating or cooling system, depending on the season. [. . . ] Cool: Thermostat controls only the cooling system. Off: Heating and cooling systems are off. CAUTION: EQUIPMENT DAMAGE HAZARD. To prevent possible compressor damage, do not operate cooling system when outdoor temperature is below 50°F (10°C). 7 Set SYSTEM switch to control the heating or cooling system. Operating Manual Fan switch Set the FAN switch to Auto or On. In "Auto" mode (the most commonly used setting), the fan runs only when the heating or cooling system is on. If set to "On, " the fan runs continuously. Use this setting for improved air circulation, or for more efficient air cleaning. Set FAN switch to choose whether the fan runs continuously or only as needed. 8 PRO TH4000 Programmable Thermostat Save money by setting program schedules It's easy to program your system for maximum energy savings. You can program four time periods each day, with different settings for weekdays and weekends. WAKE 6:00 am 70 ° LEAVE 8:00 am Set to the time you awaken and the temperature you want during the morning, until you leave for the day. Set to the time you leave home and the temperature you want while you are away (usually an energy-saving level). 62 ° 6:00 pm RETURN Set to the time you return home and the temperature you 70 ° SLEEP 10:00 pm want during the evening, until bedtime. Set to the time you go to bed and the temperature you want overnight (usually an energy-saving level). 9 62 ° Operating Manual EnergyStar® settings for maximum cost savings This thermostat is pre-set to use EnergyStar® program settings. We recommend these settings, since they can reduce your heating/cooling expenses by as much as 33%. (See next page to adjust times and temperatures of each time period. ) Heat (Mon-Fri) Wake (6:00 am) Cool (Mon-Fri) Heat (Sat-Sun) Cool (Sat-Sun) Leave (8:00 am) Return (6:00 pm) Sleep (10:00 pm) 70 ° 62 ° 70 ° 62 ° 75 ° 83 ° 75 ° 78 ° 10 [Or cancel period] [Or cancel period] 70 ° 62 ° 70 ° 62 ° [Or cancel period] [Or cancel period] 75 ° 83 ° 75 ° 78 ° PRO TH4000 Programmable Thermostat To adjust program schedules Press SET 3 times, then adjust time Set To Set Schedule 6:30 Press SET, 75 AM Set To ° Heat Wake MonTueWedThuFri then set desired temperature Set Schedule 6:30 75 AM ° 1 Press SET until Set Schedule is displayed. 2 Press or to set your weekday Wake time (Mon-Fri), then press SET. 3 Press or to set the temperature for this time period, then press SET. Make sure the temperature is set lower than the Inside temperature. · · · · Check circuit breaker and reset if necessary. Make sure power switch at heating & cooling system is on. Make sure furnace door is closed securely. Wait 5 minutes for the system to respond. 16 PRO TH4000 Programmable Thermostat In case of difficulty Temperature settings do not change "Cool On" or "Heat On" is flashing "Heat On" is not displayed "Cool On" is not displayed To restore Energy Star® default settings Make sure heating and cooling temperatures are set to acceptable ranges: · Heat: 40° to 90°F (4. 5° to 32°C). · Cool: 50° to 99°F (10° to 37°C). · Compressor protection feature is engaged. Wait 5 minutes for the system to restart safely, without damage to the compressor (see page 14). Set the System switch to Heat, and set the temperature level above the current room temperature (see page 7). Set the System switch to Cool, and set the temperature level below the current room temperature (see page 7). · · Follow these steps to restore Energy Star default settings (see page 10): 1 Press SET 3 times to display "Set Schedule. " 2 Press and hold SET and RUN at the same time for 4 seconds. 17 Operating Manual Customer assistance Grasp and pull to remove thermostat For assistance, please visit www. honeywell. com/yourhome. [. . . ] 17 Operating Manual Customer assistance Grasp and pull to remove thermostat For assistance, please visit www. honeywell. com/yourhome. Or call Honeywell Customer Care toll-free at 1-800-468-1502. To save time, please note your model number and date code before calling. Turn thermostat over to find model number and date code Accessories For accessories, please call Honeywell Customer Care toll-free at 1-800-468-1502. Cover plate . . . . . . . . . . . . . . . . Part No. 50002883-001 (Used to cover marks left by old thermostats. ) 18 PRO TH4000 Programmable Thermostat Limited 2-year warranty Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of two (2) years from the date of purchase by the consumer. [. . . ]