User manual HONEYWELL V6000

[. . . ] FLANGED BALANCING AND SHUTOFF VALVES PRODUCT DATA V6000 Kombi-F-II, Kombi-F Contents Design. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 3 Flow Data Kombi-F-II (DN15. . . DN200) . . . . . . . . . . . . . . . . . . . . . . . 4 to 15 Flow Data Kombi-F (DN250. . . DN400) . . . . . . . . . . . . . . . . . . . . . . . 16 to 19 Influence of Coolants on Flow Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Correction Factor f . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Application The hydronic balance is a significant requirement for the efficient operation of a hydronic heating or cooling installation. In an unbalanced system under or over provision of hot water to individual radiators or circuits can occur. Apart from the correct selection of radiator valves, regulation of individual circuits is also necessary and in some cases, such as in DIN 18 380, VOB part C, required by national standards. This requirement is met with Kombi-F-II and Kombi-F shutoff and balancing valves. Kombi-F-II and Kombi-F have functions shut-off, pre-setting and measuring. Design · Valve body with flanges drilled to DIN, PN 16 · Valve insert with handwheel and pre-setting display · 2 Pressure test cocks Features · Balancing through stroke limitation with digital presetting and visible pre-setting indicator · Equipped with 2 pressure test cocks for differential pressure measurement · Non rising spindle with EDD (double sealed by EDD sealing) · Pre-setting isn`t altered when handwheel is turned · Stroke limitation-screw protected by protection cap · PTFE-seat sealing · Spindle made of stainless steel · Valve body made of corrosion resistant cast iron · Available in dimensions up to DN400 Materials · Valve housing made of cast iron GG25, painted blue · Valve insert made of stainless steel with seat sealing made of PTFE · Pressure test cocks made of brass · DN15-50: Handwheel made of black plastic (Grivory GV5H) DN65 and higher: handwheel made of steel, painted black · Fairing made of plastic, black Honeywell Subject to change EN0H-0050GE25 R0706 V6000 KOMBI-F-II, KOMBI-F Specifications Medium Water, water-glycol mixture Operating temperature -10. . . 120°C (14. . . 248°F) short run 130°C (266°F) Operating pressure kvs(cv)-values max. 16 bar (232 psi) see table below and flow diagrams Please Note: · To avoid stone deposit and corrosion the composition of the medium should conform with VDI-Guideline 2035 · Additives have to be suitable for EPDM sealings · System has to be flushed thoroughly before initial operation with all valves fully open · Any complaints or costs resulting from non-compliance with above rules will not be accepted by Honeywell · Please contact us if you should have any special requirements or needs Dimensions and Ordering Information Fig. Dimensions DN 15 - DN 80 DN 15 20 25 32 40 50 65 80 100 125 150 200 (R) 1/ " 2 3/ " 4 1" 11/4" 11/2" 2" 21/2" 3" 4" 5" 6" 8" kvs(cv)-value 4. 50 (5. 27) 6. 60 (7. 72) 9. 80 (11. 5) 15. 1 (17. 7) 24. 9 (29. 1) 48. 5 (56. 7) 74. 4 (87. 0) 111 (130) 165 (193) 242 (283) 372 (435) 704 (824) Fig. Dimensions Kombi-F-II L H D K 130 225 95 65 150 225 105 75 160 225 115 85 180 225 140 100 200 280 150 110 230 280 165 125 290 365 185 145 310 395 200 160 350 430 220 180 400 495 250 210 480 530 285 240 600 665 340 295 Fig. Dimensions DN 250 - DN 400 nxd 4 x 14 4 x 14 4 x 14 4 x 18 4 x 18 4 x 18 4 x 18 8 x 18 8 x 18 8 x 18 8 x 22 8 x 22 Weight 3. 5 kg 4. 1 kg 4. 8 kg 6. 6 kg 9. 0 kg 11. 5 kg 18. 5 kg 24. 5 kg 40. 0 kg 79. 0 kg 91. 0 kg 170 kg OS-No. [. . . ] This condition is met by water at a temperature of 20°C (68°F). For fluids with another density the following formula can be applied: Medium m kv Medium = ---------- × ------------------------p 0 Correction Factor f When the density is expressed in t/m³ instead of kg/m³ the correction factor f is the result. [. . . ]