User manual HONEYWELL XL 1000B-C

[. . . ] Excel Web XL1000B/C HONEYWELL EXCEL 5000 OPEN SYSTEM INSTALLATION INSTRUCTIONS TABLE OF CONTENTS Overview of Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Terminal Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 LonWorks Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Ethernet Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Specifically, it is lit whenever an Ethernet jack has been inserted into the corresponding port and the software has established the Ethernet link. It is dark when the link has been disabled. Ethernet Activity LED The LED marked " " indicates whether or not the Ethernet link is currently active. Specifically, when it flashes, this means that signals are being transmitted / received on the Ethernet network; when it is dark, no messages are being transmitted/received. LEDs L1 and L2 At present, these LED's are not in use. 5 EN1B-0256GE51 R0609 EXCEL WEB CONTROLLER ­ INSTALLATION INSTRUCTIONS Reset Button DIN Rail Mounting/Dismounting 17 mm The reset button can be pressed only using a long, thin tool (e. g. Pressing it reboots the Excel Web controller's operating system and restarts the application. MOUNTING IMPORTANT To allow the evaporation of any condensation resulting from low shipping / storage temperatures, keep the controller at room temperature for at least 24 h before applying power. US requirement, only: This device must be installed in a UL-listed enclosure offering adequate space to maintain the segregation of line voltage field wiring and Class 2 field wiring. In order to meet the criteria for CE certification, the XL1000 controller must be mounted inside an electrical panel. Before Installation slots for DIN rails (center-to-center distance = 100 +3 mm) fastening plate Fig. Housing base (view from below) The Excel Web controller can be mounted onto DIN rails as follows (refer also to Fig. Hang the upper slot onto the upper DIN rail. Swing the unit down until it is flush with the lower DIN rail. Slide the fastening plate and corresponding screw in the oval hole up against and behind the bottom edge of the lower DIN rail and screw it firmly into place. If necessary, the swivel cover can be locked by inserting a small string lock, lead seal, or screw into either one of the two openings provided. The unit is dismounted by loosening the fastening plate and lifting the unit out of place. Dimensions Allow 30 mm clearance for opening swivel cover. 190 LON CF LON 1 2 3 Allow 30 mm clearance for accessing interfaces. 36. 5 278 4. 4 +/- 0. 3 0. 6 60. 6 step 1 141. 5 +/- 0. 3 100 mm 12 220 +/- 0. 3 5 +/- 0. 3 Fig. Dimensions (in mm) The Excel Web has the following dimensions (W x L x H): 278 x 190 x 61 mm. Its pollution degree (2) makes it suitable for use in residential controls, commercial controls, in a clean environment, or non-safety controls for installation on or in appliances. The Excel Web is suitable for mounting on a standard rail (DIN EN 50022-35 x 7, 5), on walls or in panels, as well as for installation in appropriately-sized wiring cabinets or fuse boxes. 30 mm) to access the interfaces and to open the swivel cover (see Fig. 8). step 2 step 3 step 4 fastening plate Fig. Mounting the Excel Web on to two DIN rails Wall/Panel Mounting/Dismounting The Excel Web controller can be mounted on walls or in panels in any desired orientation. However, mounting the Excel Web controller upside down on ceilings should be avoided, insofar as the swivel cover would then swing open. EN1B-0256GE51 R0609 6 EXCEL WEB CONTROLLER ­ INSTALLATION INSTRUCTIONS 4. 4 +/- 0. 3 36. 5 Power is supplied via terminals 1 and 2 of the lower removable terminal plug. The removable terminal plug permits individual Excel Web controllers to be disconnected from the power supply without disturbing the operation of other devices powered by the same source. NOTE: Do not reverse the polarity of the power connection cables, and avoid ground loops (i. e. [. . . ] The following USB host networking adapter has been approved: BELKIN DIRECT CONNECT (BELKIN order no. : F5U104 or F5U104G at www. belkin. com). For access via USB, the Excel Web has a permanent default IP address 192. 168. 252. 20 and Network Mask 255. 255. 255. 0. Your PC's IP address must match the Excel Web controller's default IP address subnet: We recommend using 192. 168. 252. 21 and Network Mask 255. 255. 255. 0. Option 2: Dedicated Ethernet Interface For access via Ethernet, the Excel Web has a permanent default IP address 192. 168. 253. 20 and Network Mask 255. 255. 255. 0. Your PC's IP address must match the Excel Web controller's default IP address subnet: We recommend using 192. 168. 253. 21 and Network Mask 255. 255. 255. 0. [. . . ]