User manual HONEYWELL XL1000

[. . . ] XL 1000 Series FOR SMOKE CONTROL HONEYWELL EXCEL 5000 OPEN SYSTEM INSTALLATION AND COMMISSIONING INSTRUCTIONS CONTENTS Operational Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Before Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Neuron chip lacks LONWORKS interface program. Remedy: Use Excelon or LonMaker, set XL1000 online. XL1000 probably experiencing continuous watchdog resets, or external memory or EEPROM is corrupt. XL1000 is unconfigured but has an application. Remedy: Commission XL1000. Ethernet Activity LED The LED marked " " indicates whether or not the Ethernet link is currently active. Specifically, when it flashes, this means that signals are being transmitted / received on the Ethernet network; when it is dark, no messages are being transmitted/received. 2 3 LEDs L1 and L2 At present, these LED's are not in use. 4 Reset Button The reset button can be pressed only using a long, thin tool (e. g. Pressing it reboots the XL1000's operating system and restarts the application. 5 6a Return XL1000 to factory. Mounting Before Installation IMPORTANT To allow the evaporation of any condensation resulting from low shipping / storage temperatures, keep the controller at room temperature for at least 24 h before applying power. In order to meet the criteria for CE certification, the XL1000 must be mounted inside an electrical panel. 6b Return XL1000 to factory. 6c OFF for 1 15 s, depending on application size and system XL1000 is unconfigured but clock. Afterwards, service LED has an application. Remedy: repeatedly flashes ON for 1 s Commission XL1000. LED remains OFF after a short ON duration. XL1000 is configured and running normally. XL1000 received a WINK command from LONWORKS; other physical outputs are unaffected. 7 Dimensions The XL1000 has the following dimensions (W x L x H): 278 x 190 x 61 mm. Its pollution degree (2) makes it suitable for use in residential controls, commercial controls, in a clean environment, or non-safety controls for installation on or in appliances. The XL1000 is suitable for mounting on a standard rail (DIN EN 50022-35 x 7, 5) for installation in appropriately-sized wiring cabinets. 30 mm) to access the interfaces and to open the swivel cover (see Fig. 9). 8 In case of a problem, check if the LONWORKS service LED's behavior is changed by resetting the XL1000 using the reset button. Please contact Honeywell if this does not solve the problem. Ethernet LEDs The XL1000 is equipped with two Ethernet LEDs (see Fig. 3). EN1B-0409GE51 R0908A 10 XL1000 Mounting Allow 30 mm clearance for opening swivel cover. step 1 190 LON CF LON 1 2 3 100 mm Allow 30 mm clearance for accessing interfaces. 36. 5 278 4. 4 +/- 0. 3 step 3 step 4 0. 6 60. 6 step 2 fastening plate 141. 5 +/- 0. 3 Fig. Mounting the XL1000 onto two DIN rails 12 220 +/- 0. 3 5 +/- 0. 3 Wall/Panel Mounting/Dismounting The XL1000 can be mounted on walls or in panels in any desired orientation. However, mounting the XL1000 upside down on ceilings should be avoided, insofar as the swivel cover would then swing open. Fig. [. . . ] XL800 Relay Output Modules type XFL824 XFLR824 XS824-25 description housing Terminals 72 COM B 73 74 24 V~ 24 V~0 71 COM A COM A COM B 24 V~ 24 V~0 75 76 77 78 LONWORKS Relay Output Module dark-gray LONWORKS Relay Output Module dark-gray with manual overrides terminal socket; can be fitted with long (red) cross connector (incl. in scope of the delivery) light-gray NO NC COM CON Relay block 1 Relay block 2 11 12 13 14 NO 21 NC 22 COM 23 CON 24 NO NC COM CON 31 32 33 34 NO NC COM CON 41 42 43 44 NO NC COM CON 51 52 53 54 NO NC COM CON 61 62 63 64 25 Cross connector (can be removed, as desired) Features · 6 relays (changeover contacts), arranged in two blocks · XFLR824AU: 6 manual overrides · Low and line voltage allowed, see WARNING. Fig. Terminal assignment and internal connections of Relay Output Modules 1 2 3 4 5 6 Fig. XFLR824AU Relay Output Module with terminal socket Legend 1 2 3 4 5 6 Service button S1 Hex switch S2 (no function) Manual overrides Status LEDs Service LED Power LED Functionality of service LED and power LED: see Table 24 and following. EN1B-0409GE51 R0908A 28 XL1000 Description of the I/O Modules Table 21. [. . . ]