User manual HOOVER CHELSEA OVENS

[. . . ] REMEMBER: · When using cleaning tools ensure that the cleaner is kept in the upright (parked) position. This will avoid possible damage to the carpet, floor or floor covering · Keep hands, feet, loose clothing and hair away from rotating brushes · After use, switch the cleaner off and remove the plug from the electricity supply. Always switch off and remove the plug before cleaning the appliance or attempting any maintenance task DO NOT: · Position the cleaner above you when cleaning stairs · Use your cleaner out of doors, on wet surfaces or for wet pick-up · Pick up matches, hot ash, cigarette ends, hard or sharp objects or anything that may damage the cleaner · Spray with, or pick up, flammable liquids, cleaning fluids, aerosols, or their vapours, as this may cause risk of fire/explosion · Run over the supply cord when using your cleaner or remove the plug by pulling on the cord · Stand on, or wrap the power cord around arms or legs when using your cleaner · Continue to use your cleaner if it appears to be faulty. If the supply cord is damaged stop using the cleaner IMMEDIATELY. [. . . ] The exceptional suction may cause the cleaning tool to become locked to a surface, restricting airflow. In such cases, simply lift the tool away from the surface. Make sure the handle is fully clicked into place after use. 11 EMPTYING THE DUST CONTAINER For peak performance we recommend the dust container is emptied on a regular basis. Filling must not exceed the maximum level indicated on the dust level viewing window. REMEMBER ­ Always switch off and unplug the machine from the electricity supply before maintaining your cleaner. 12 Dust container release Holding the pre-motor filter cover, press the dust container release button and lift the dust container from the cleaner. 6 6 Stair cleaning mode To use the cleaning tools, press the stair cleaning release button and lift the handle from the cleaner body. The flexible hose fitted with the extended Zoom Cleaning Tool with integrated crevice tool will reach up a full flight of 13 stairs. 7 Positioning the cleaner for maximum safety Your cleaner incorporates an Anti-Tip Design. Ensure the cleaner is positioned up against the bottom step. 12 7 13a 13 Dust container emptying The 2-stage opening system minimises the escape of dust when emptying. To release fine dust first, firmly hold the dust container and push down the hand grip at the back of the container with your palm (13a). 13b 6 www. hoover. co. uk Rotate hand grip with your fingers to open fully the dust container and release the remaining debris (13b). Reverse operation to close the dust container. 7 www. hoover. co. uk Maintaining performance Maintaining performance FILTER SYSTEM There are 3 filters and a dust screen. After 12 months you may wish to replace the exhaust filter with a new one. This part can be ordered through the GIAS Service Division at 01204 - 556111 or purchased on www. hoover. co. uk at Hoover Accessory Shop (Part no. 04365127 T84). 15b 16a The HEPA Anti Odour filter requires little or no maintenance and should only need checking if there is a drop in performance. To access the HEPA Anti Odour filter, remove the dust container from the cleaner (16a). Press the filter release button to release the exhaust filter (16b and 16c). Shake the filter to remove fine dust particles. Do not wash or scrub the filter. 16b 16c www. hoover. co. uk 8 www. hoover. co. uk 9 Maintaining performance Before calling Hoover User checklist If your cleaner has stopped working completely, run through the following check list: i) Is there a working electricity supply to the cleaner?A thermal cut out switches off the cleaner automatically to prevent overheating if the cleaner is used when the dust container is over full, or the filters require cleaning, or there is a blockage. If this should happen switch off and unplug the machine from the electricity supply. To correct the fault please refer to sections 12-18. 19 CHECKING BELT AND BRUSHES/ REPLACING THE BELT REMEMBER ­ Always switch off and unplug the machine from the electricity supply before checking the brushes, belt or removing the hood. 19a i) Remove the flexible hose from the cleaner ­ twist hose end connectors to remove hose at both ends as shown in section 17. Using a crosshead screwdriver remove 4 hood screws as shown (19a). [. . . ] (refer to section 17) Is there a blockage in the cleaner base?(refer to section 18) Are the filters blocked?(refer to sections 14, 15 and 16) Are the brushes rotating?(refer to section 19) 19c v) vi) 19d vii) viii) 19e ix) x) REMEMBER - If there is any doubt, call the Hoover Advice Helpline (open 7 days a week) on 08705 400600. [. . . ]