User manual HOOVER H7238

[. . . ] STATIC ELECTRICITY: some carpets can cause a small build up of static electricity. Any static discharge is not hazardous to health. REMEMBER: · When using cleaning tools ensure that the cleaner is kept in the upright (parked) position. This will avoid possible damage to the carpet, floor or floor covering · Keep hands, feet, loose clothing and hair away from rotating brushes · After use, switch the cleaner off and remove the plug from the electricity supply. [. . . ] It is ideal for upholstery, stair cleaning and many other uses. 11 Dusting brush The dusting brush is stored on the cleaner body and fits on the crevice tool. It is ideal for gentle dusting on all surfaces. REMEMBER - Make sure handle is fully clicked into place after use. 4 10b Maintaining performance 5 STAIR CLEANING REMEMBER ­ Always work with the cleaner below you. The exceptional suction may cause the cleaning tool to become locked to a surface, restricting airflow. In such cases, simply lift the tool away from the surface. Make sure the handle is fully clicked into place after use. 11 EMPTYING THE DUST CONTAINER For peak performance we recommend the dust container is emptied on a regular basis. Filling must not exceed the maximum level indicated on the dust level viewing window. 6 6 Stair cleaning mode To use the cleaning tools, press the stair cleaning release button and lift the handle from the cleaner body. The flexible hose fitted with the extended Zoom Cleaning Tool with integrated crevice tool will reach up a full flight of 13 stairs. 7 Positioning the cleaner for maximum safety Your cleaner incorporates an Anti-Tip Design. Ensure the cleaner is positioned up against the bottom step. 12 REMEMBER ­ Always switch off and unplug the machine from the electricity supply before maintaining your cleaner. To access the exhaust filter, remove the dust container from the cleaner (16a). Press the filter release button to release the exhaust filter (16b and 16c). Allow to air dry thoroughly before refitting. REMEMBER ­ To maintain optimum cleaning performance it is imperative to wash the HEPA pre-motor filter and foam pre-motor filter every 5 dust container empties. 18a 18b 14d 14e 15a 15b 16a 16b 16c www. hoover. co. uk 8 www. hoover. co. uk 9 Maintaining performance Before calling Hoover User checklist If your cleaner has stopped working completely, run through the following check list: i) Is there a working electricity supply to the cleaner?A thermal cut out switches off the cleaner automatically to prevent overheating if the cleaner is used when the dust container is over full, or the filters require cleaning, or there is a blockage. If this should happen switch off and unplug the machine from the electricity supply. To correct the fault please refer to sections 12-18. 19 CHECKING BELT AND BRUSHES/ REPLACING THE BELT REMEMBER ­ Always switch off and unplug the machine from the electricity supply before checking the brushes, belt or removing the hood. 19a i) Remove the flexible hose from the cleaner ­ twist hose end connectors to remove hose at both ends as shown in section 17. Using a crosshead screwdriver remove 4 hood screws as shown (19a). Turn cleaner over and lift off hood (19b). Remove agitator brush and belt assembly by pulling upwards out of the cleaner base (19c). Replace belt, if worn or broken, by looping the new belt over the metal motor spindle (19d). [. . . ] (refer to section 18) Are the filters blocked?(refer to sections 14, 15 and 16) Are the brushes rotating?(refer to section 19) 19c v) vi) 19d vii) viii) 19e ix) x) REMEMBER - If there is any doubt, call the Hoover Advice Helpline (open 7 days a week) on 08705 400600. They may be able to assist you over the telephone. 19f www. hoover. co. uk 10 www. hoover. co. uk 11 Important information Genuine Hoover Spares Always replace parts with Genuine Hoover Spares. [. . . ]