User manual HOOVER HEH 604

[. . . ] 10 General maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 UNPACKING OF THE APPLIANCE Inside the appliance you will find a plastic bag containing the fixing brackets required for installing the hob in the worktop. RECOMMENDATIONS TO GET THE BEST FROM YOUR APPLIANCE, PLEASE READ THE FOLLOWING CAREFULLY. Please keep the operating and installation instructions in a safe place for future reference. Before fixing the hob, note the serial number of the appliance just in case you should require repairs from our after sales service organisation at some time in the future. Rating plate (located under the lower casing of the hob) · All accessible parts of the hob will become hot while in operation. [. . . ] 1 - Operations to be carried out on the existing connection (if necessary) : . Terminal block Cable clamp Shunts bars Earth green/ yellow wire 1 . The hob is supplied for a single phase connection : 220-240 V~ or two phase : 220-240 V2~. . Remove the screws retaining the terminal block which contains the shunt bars and the conductors of the supply cord. Unscrew the cable clamp to release the power supplying cord. Pull out the supply cord. 5 2 - Operations to be carried out to make a new connection: . Choose the supply cord in accordance with the recommendations in the table on next page. The hob must be in situation as shown : Earth Terminal . Strip the end of each conductor of the supply cord on a 10 mm length, by taking in account the requested length of the cord for the connection on the terminal block. According to the installation and with the help of shunt bars which you should have recovered in the first operation, fix the conductor as shown on the chart. Engage the earth wire yellow/green on the earth terminal, screw the nut and verify the continuity of the earth. Fix the cover. 6 INSTALLATION: "ELECTRICAL CONNECTION" Connection of origin Single phase 220-240V~ FUSE C ABLE Type A e ra C onnection to the terminal block To shunt : make a bridge with a shunt bar Two phase 220-240V2~ 20A Three phase 220-240V3~ 20A Three phase 380-415 V3N~ 16A 20A H05RR-F H05RR-F H05RR-F H05VV-F 4 G 2, 5 mm² 12345 H05RR-F H05VV-F 5 G 1, 5 mm² 12345 3 G 2, 5 mm² 12345 3 G 2, 5 mm² 12345 E PH N PH PH E PH PH PH E PH PH PH N E 1rst Phase Shunt Shunt Neutral Shunt Earth 1rst Phase 1-2 Shunt 2-3 Shunt 2nd Phase 4-5 Shunt Earth 1rst Phase 1-2 Shunt 2-3 2nd Phase Shunt 4-5 3rd Phase Earth 1rst Phase 1-2 2nd Phase 3rd Phase 3-4 Neutral 5 Shunt Earth 1 2 3 4-5 IMPORTANT : Blue wire = Neutral Yellow/green wire = Earth For the connection to the terminal block, you must : . do not forget to fix the earth wire (yellow/ green) on the earth terminal n° 6. Example of connection Three phase 220-240V3~ : The earth wire must be clipped at this place. Tighten the nut fully home. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 PRESENTATION / TECHNICAL DATA HEH 604 4 ELECTRICAL HOT PLATES Speed protected hot plate 1500 W - Ø 145 Hot plate 1500 W - Ø 180 Speed protected hot plate 2000 W - Ø 180 Hot plate 1000 W - Ø 145 Power-on indicator lights Overall dimensions (cm): Width : 59 Depth : 51 Building-in dimensions (cm) - (see chapter "Installation") Width : 56 Depth : 48 Total electrical power: 6 kW In order to improve the quality of the products, HOOVER may carry out modifications linked to technical improvements. Appliance meeting with the standard CEE 89/336, and 73/23. 8 THE HOT PLATE THE STANDARD ELECTRICAL HOT PLATE This is a cast-iron hot plate, controlled by a 7 positions commutator. Each position corresponds to a permanent and progressive temperature according to the marks 1, 2, 3, 4, 5 and 6. RAPID SELF-PROTECTING ELECTRIC HOT PLATE (with a red dot in the centre) This a cast-iron hot plate, controlled by a 7 positions commutator. As with the previous hot plate, each position corresponds to a permanent and progressive temperature according to the marks 1, 2, 3, 4, 5 and 6. An internal thermostat cuts off of the power supply if there is any abnormal heating. (If, for example, a hot pate is working without a pan on it). BEFORE USING THE ELECTRIC HOT PLATE: · Before using the electric hot plate for the first time, let it heat up for a few minutes, without a pan, at maximum temperature to let the protective coating harden. HOW TO USE: · For best results, it is advisable to start on the maximum heat and then turn back to an intermediate temperature taking into account the type and volume of the food. [. . . ] If you clean the surface when it is hot, you may tarnish it. THE KNOBS For thorough cleaning, the control knobs can be removed by pulling them upwards. Clean exclusively with soapy water and dry well before replacing them. THE HOT PLATE Heat it for a while if necessary, to burn the deposits. [. . . ]