User manual HOOVER HGQ640

[. . . ] When there is an accessible space between the built-in hob and the cavity below, a dividing wall made of insulating material should be inserted (wood or a similar material) (fig. 3). AUS ø 50 mm QC ø 135 mm UR ø 110 mm SR ø 75 mm R ø 100 mm ø80 ø145 PE PE Electric plate Installed gas Type/Power: G20 20mbar* G30 28-30mbar Installation class Voltage/Frequency Electrical imput power Electronic ignition Product dimension WXD (mm) 160x265 mm PE (METHANE) (GPL) V/Hz 8, 75 kW 636 g/h 220-240/50 si 11, 25 kW 818 g/h 220-240/50 si * Manufacturer setting IE cat. II2H3 + Important - The diagram below shows how the sealant should be applied. Plan 60 Plan 75 The Hob unit is fitted by attaching the Fixing Clamps supplied, using the holes at the base of the unit. Fig. 1 accessible space This appliance has been designed for non-professional, i. e. [. . . ] It is possible to use other types of gas after carrying out simple modifications. Warning: If gas can be smelt in the vicinity of this appliance turn off the gas supply to the appliance and call the engineer directly. Do not search for a leak with a naked flame. IE GB 3 4 GB IE ELECTRICAL CONNECTION Check the data on the rating plate, located on the outside of the unit, to ensure that the supply and input voltage are suitable. Before connection, check the earthing system. If this regulation is not complied with, the Manufacturer will not be responsible for any damage caused to persons or property. If a plug is not already attached, fit a plug appropriate to the load indicated on the rating plate. The earth wire is coloured yellow/green. Where the Hob is connected direct to the electricity supply, a circuit breaker must be fitted with at least a 3 mm contact spacing when in the open position. If the power supply cord is damaged this is to be replaced by a qualified engineer so as to prevent any potential risk. The earth wire ( green a yellow coloured) must be at least 10 mm longer than the live and neutral wires. The section of the cable used must be of the correct size in relation to the absorbed power of the hob. Please check rating plate for the power details and ensure that the power supply cord is of the type H05RR-F, H05VV-F, H05V2V2-F. To prevent any potential damage to the hob please carry out the installation following this sequence: GB IE 1/2 GAS CONICAL A) As illustrated, assemble parts in sequence: A) fixed pipe B) washer C) Elbow fitting with tapered thred connection 2) Tighten the joints with the Spanners, remembering to twist the pipes into position. 3) Attach fitting C to mains gas supply using rigid copper pipe or flexible steel pipe. MAINS SUPPLY LIVE EARTH L BROWN WIRE GREEN/YELLOW WIRE BLUE WIRE POWER CABLE NEUTRAL N For some models a conic link is furnished to outfit for the installation in the countries where this type of link is obligatory; in the following figures it is pointed out how to recognize the different types of links. In every case the cylindrical part of the link has to be connected to the hob. Fig. 5 GAS CONNECTION These instructions are for Fitters qualified for installation of equipment in line with the relevant national standard. All work must be carried out with the electricity supply disconnected. The rating plate on the hob shows the type of gas with which it is designed to be used. It is possible to use other types of gas after carrying out some simple modifications. (See the instructions in the following paragraphs). connection to the mains gas supply or gas cylinder should be carried out according to the relevant national standards, after having checked that it is regulated for the type of gas with which it will be supplied. If it is not correctly regulated follow the instructions in the paragraph entitlet «Adaption for different types of gas». For liquid gas (cylinder gas) use pressure regulators which comply with the relevant national standards. [. . . ] The symbol on the product indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. Disposal must be carried out in accordance with local environmental regulations for waste disposal. For more detailed information about treatment, recovery and recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. COVER The cover is available as optional accessory. [. . . ]