User manual HOTPOINT-ARISTON HB7850

[. . . ] Correct replacement is identified by colour coding or the marking on base of plug. WARNING: Do not use plug unless fuse holder is in locked position. Changing the Plug Cut off and dispose of the supplied plug if it does not fit your socket. WARNING: To avoid a shock hazard do not insert the discarded plug into a socket anywhere else. Green and yellow (Earth) wire to terminal marked `E', symbol , or coloured green and yellow. IMPORTANT: WIRES IN THE MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE: Green/Yellow Earth Blue Neutral Brown Live If you change the plug, the colour of wires in the mains lead may not correspond with the colour of the markings identifying terminals in the plug. You should therefore wire it as shown. 13A ASTA approved fuse to BS1362. Blue (Neutral) wire to terminal marked `N' or coloured black. Brown (Live) wire to terminal marked `L' or coloured red. Cord clamp Changing the Mains Lead A special lead can be ordered form Hotpoint Service UK: 08709 066 066 or Republic of Ireland: 1850 302 200 If you have damaged the existing lead or require a longer one a charge will be made. [. . . ] Stabilise the appliance, see `Adjusting the feet' opposite. Fig 1 Fig 2 Fig 3 Sink Waste System Note: Ensure the sink outlet pipe has a minimum diameter of 32 mm. Untie the end of the GREY drainage from the rear of the appliance. Reposition `Hooked End Support' as required along GREY drainage hose. If fitting an under sink waste disposal unit (Fig 3), cut out the membrane, bung or blanking plug (Fig 4 and 4a). Attach the GREY drainage hose to the under sink waste disposal unit securely, using a Jubilee clip. Raise the hose to a minimum height of 800 mm to avoid syphoning. Fig 4 - Before Fig 4a - After 5. Adjust the Feet. . . This must only be done when the machine is upright. q Release locking rings on the two front feet. q Screw feet in or out until appliance is standing firm and level. q Ensure all feet are in firm contact with the floor. q Tighten the locking rings on the front feet. Note: Your appliance may become noisy or move about the floor if it has not been stabilised. 9. Turn on the water supply to the appliance. q Reduces the quantity of water used for rinsing. q Not available with programme `A'. Super Rinse For large wash loads, wash items for young children and people with sensitive skin. q Increases the water level of the last two rinses on all programmes except programme `A' and the wool programme `K', which increases automatically. Time Saver Save 43 minutes on programme D and up to 25 minutes on any other wash programme. q Not available with programme `A' or the wool programme `K'. Note: Remember to cancel buttons after use! Automatic Features Pulse Spin Helps reduce wear and tear on your wash items. Pulse spin is an automatic function where a long steady spin is followed by a 30 second burst at the maximum speed of your appliance to enable safer, more efficient water extraction. Intelligent Care Your appliance has an inbuilt feature to prevent it spinning with an unbalanced load, avoiding excessive vibration and prolonging the life of the appliance. 12 Weight of Wash Load Two examples of typical wash loads for different types of fabric Washcare Tips Before washing laundry:- q Pre-treat stains. COTTON 2 Bath Towels 5 Shirts 6 Blouses 1 Set of Pyjamas 4 Sets of Underwear q Close zips, tie belts, strings etc. . . q Remove sharp objects or coins from pockets as they may damage clothes. q Limit size of absorbent loads ie. ; towels, to 3kg (7lb) to give good washing/rinsing results. q Check wash labels as some items may require a cool programme. q Wash non-colour fast items, woollens or really dirty clothes separately as they may affect other items. q Laundry will not wash properly if you over load your appliance. q Laundry without a wash label should not be machine washed. = 5. 5kg SYNTHETIC 2 Children's Dresses 4 Shirts 4 Blouses 1 Set of Pyjamas 4 Sets of Underwear = 3kg Spin only option. . . IMPORTANT INFORMATION: Before selecting a programme, ensure the mains button is in the `OFF' position. [. . . ] See `Installation' pages 4, 5, 6 & 7. q q Have you used the correct amount of detergent suitable for automatic washing appliances?See `Detergent & Fabric Conditioner' page 15. If you have used the wrong type, flush out your appliance by selecting a rinse programme. Follow instructions on the detergent pack, taking into consideration load size, soiled loads and water hardness. It makes a noise or vibrates during a spin programme. . . If the noise is excessive you should check: q Has the transit bracket been removed? [. . . ]