User manual HOTPOINT-ARISTON HB9316

[. . . ] The appliance is designed specifically for domestic use and responsibility will not be accepted for use in any other installation. * The guarantee is subject to the provisions that the appliance: (a) (b) (c) (d) Has been used solely in accordance with the Users Instruction Book. Has been properly connected to a suitable supply voltage as stated on the rating plate attached to this equipment. Has not been subjected to misuse or accident or been modified or repaired by any person other than the authorised employee or agent. Has been correctly installed. Disposal of your product To minimise the risk of injury to children please dispose of your product carefully and safely. [. . . ] Any boiled over liquids or food are spilled onto the control zone. Any extended pressure is placed on the control zone. These could cause the word `DEF' to appear on the display, accompanied by a beep. The temperature indicators will blink and the cooking zone(s) in use will turn off. To stop the beep, remove the cause of the malfunction. To stop the temperature indicators blinking, press the and the control zone(s) can be used again. key for 3 seconds Safety cut out If the user inadvertently forgets to turn off one or more cooking zones, the corresponding control is automatically put out of order after a given amount of time. Power Level Maximum Operation Time 6 hours 5 hours 4 hours 3 hours 1. 5 hours 1-2 3-4-5 6-7-8 9 - 10 - 11 12 - 13 - 14 12 Using Your Hob Overheating Prolonged use of the hob could cause the electronic components to overheat. A thermal protection device momentarily sets a reduced power (level 3) on the right hand cooking zones. The temperature indicators blink to show you that this safety measure has been taken. When the temperature returns to normal, the temperature indicators stop blinking and the cooking zones can once again be used at higher power levels if required. Should the temperature of the electronic components continue to rise, the cooking zones are locked until the temperature drops - as indicated by the blinking of the 3 points on each of the four temperature indicators. Cooking time programming You can programme the cooking zones seperately or simultaneously and for different cooking times of up to 3 hours. Once you have selected the heating power, programme the cooking time as follows: q Press the Timer key for the cooking zone (the corresponding indicator light blinks), 0. 00 is displayed. For stubborn stains or heavy soiling use any of the following materials, and finish off with conditioner. Powder Cleanser ­ Mineral deposits that are present in hard water, and some foods, may cause `discolourations' that appear in the form of grey or brown stains. The stains sometimes appear to be in or under the glass surface. If there are some persistent stains after using any of the other recommended cleaning materials, powder cleanser may be applied, following the manufacturers instructions. Do not use abrasive cleaners or the powder cleanser on the painted metal framework. Cleaner Conditioner ­ Regular use of the conditioner will make the surface easier to clean thus ensuring that years of heavy abrasive cleaning do not progressively dull the surface. If the hob is scratched through accident or misuse, soil that collects will appear as fine brown lines; these are not fully removable but can be made less obvious by the daily use of cleaner conditioner. Cooking performance is in no way affected by scratches on the surface. Pans with aluminium bases should be lifted rather than dragged across the hob surface. This will avoid metal rubbing off the pan onto the glass. Such marks are easily removed by the powder cleanser provided they are not subsequently baked on for long periods at high temperatures. [. . . ] 4 Fixing Brackets HOB FROM BELOW Fixing Brackets HOB TOP Cut Out WORKTOP Fixing Brackets 20 Installation ELECTRICAL CONNECTION THIS APPLIANCE MUST BE EARTHED. The electrical safety of this appliance can only be garanteed when the latter is correctly and efficiently earthed, in compliance with regulations on electrical safety. The manufacturer denies all responsibility for damage resulting from a system which has not been earthed correctly. Before powering the appliance, check whether the technical characteristics featured on the appliance data plate correspond with those of the electrical system (wire section, protection devices), which should be suitable for the appliance maximum power. [. . . ]