User manual HOTPOINT-ARISTON HBRZA50

[. . . ] FREEZER - MODELS RZA50 INSTRUCTIONS FOR INSTALLATION & USE GETTING STARTED: STEP 1 Choose a location for your freezer, away from any heat sources and allow adequate ventilation - 100mm (4 inches) gap above. To ensure that your freezer runs reliably and efficiently follow these steps. STEP 2 Move the freezer into position, using the sides of the cabinet. Take care to avoid damaging the refrigerant circuit pipe work on the rear. SAFETY & INSTALLATION CONTROLS STEP 3 Level the freezer by adjusting the front feet. This will stop rocking or vibration and keep the door aligned. NB. [. . . ] As the frost begins to melt, use the supplied plastic scraper to remove frost. Never use sharp metal tools to remove frost as they may damage your freezer beyond repair. Sponge out excess defrost water which collects at the bottom of the freezer. NOTE : When defrosting is complete, clean the interior thoroughly, see CLEANING section, next page. Unwrap food and replace. CLEANING & MAINTENANCE 12 Cleaning Cleaning WARNING: Switch off electrical supply and pull out mains plug before cleaning. Interior WARNING: Do not use abrasive powder, household cleaner, bleach or wax polish to clean the interior, they will leave a smell in the freezer. Remove stored food, wrap or cover it and place into insulated containers to keep frozen whilst cleaning. Wash in warm water and washing up liquid using a soft cloth, dry thoroughly. Wipe the interior and fittings with a clean cloth wrung out in a solution of either one teaspoon of bicarbonate of soda to one pint of water or MiltonTM sterilising fluid, diluted according to the manufacturer's instructions. Dry the interior thoroughly with a clean cloth before replacing fittings and food. Note : It is important to ensure that cleaned drawers are thoroughly dried before refitting into the freezer compartment. Exterior WARNING: Do not use abrasive powder, household cleaner or bleach, they can damage the exterior of your freezer. Use a clean soft cloth wrung out in warm water and washing up liquid to wipe the exterior surface, dry thoroughly. Use a soft brush or vacuum cleaner to remove dust from underneath the freezer and from the compressor and condenser situated at the back of the freezer. Door Seal Use warm water and a clean soft cloth to wipe along and in between the creases of the door seal, dry thoroughly. Take care not to damage the seal and avoid using sharp objects. WARNING: Do not use detergent, it will damage the seal. Going Away If you are going away and don't want to use your freezer, switch off the electricity supply and pull out the mains plug. Remove food and follow the cleaning instructions above. Note : Leave the door ajar to prevent an accumulation of odours. 13 CLEANING & MAINTENANCE Door Reversal You will need a cross head screwdriver, a flat blade screwdriver and a 5mm spanner to carry out this procedure. Our Service Department can arrange for an Engineer to do the conversion for you but a charge will be made. WARNING: Switch off electrical supply and pull out the mains plug. [. . . ] This can be louder when it first switches on. This sound will reduce over the first few months. q Gases flowing through the pipes can produce gurgling, bubbling, roaring or humming noises. q The temperature control can make a clicking noise when it turns the motor on and off. q Expansion and contraction of parts inside the freezer can produce a cracking noise as they rapidly change temperature. TROUBLESHOOTING 17 Hotpoint guarantee "Satisfaction guaranteed or your money back" We give you a unique `satisfaction guaranteed' promise - valid for 90 days - after you have purchased your Hotpoint appliance. If there is a technical problem simply call Hotpoint Repair service or visit our web-site at www. theservicecentre. co. uk and where necessary, we will arrange for an engineer to call. If the technical problem is not resolved under this guarantee, we will replace your appliance or, if you prefer, give you your money back. All Hotpoint appliances carry a fully inclusive 12 month parts and labour guarantee as well as free replacement parts for the first 5 years (except microwaves, selected integrated appliances and cooker hoods, which have a one year guarantee) provided that they are fitted by a Hotpoint engineer. [. . . ]