User manual HOTPOINT-ARISTON TCL G31X

[. . . ] Where to put your dryer Ventilation Door reversal instructions Water drain Electrical connection Before you start using your dryer Sorting your laundry Wash care labels Special clothing items Drying times General safety Disposal Saving energy and respecting the environment Switching off the electricity Cleaning the filter after each cycle Empty the water container after each cycle Check the drum after each cycle Cleaning the condenser unit Cleaning the dryer Keep this instruction booklet on hand in order to refer to it when necessary. Take it with you when you move, and should you sell this appliance or pass it on to another party, make sure that this booklet is supplied along with the dryer so that the new owner may be informed about warnings and suggestions on how the appliance works. Read these instructions carefully; the following pages contain important information on installation and suggestions on how the appliance works This symbol reminds you to read this booklet. For your Condenser dryer to operate efficiently, you must follow the regular maintenance schedule shown below: You MUST clean the fluff filter after EVERY drying cycle. [. . . ] If the option is available there will be one beep and the option light next to the button lights to confirm the selection. Progress Lights: Drying (Séchage), Cool Tumble (Refroidissement), End (Fin) / Delay Lights: (3hr, 6hr, 9hr) When the light next to the delay button is on, these lights flash to indicate the delay time selected. During other programmes they indicate the progress of the dryer, each one comes on as the corresponding phase starts. Time Delay (Départ Différé) The start of some programmes (see Start and Programmes) can be delayed for up to 9 hours in 3hr steps. Ensure the water bottle is emptied before setting a delayed start. When a delayed start is in progress the light next to the delay button will be on and the selected delay period light will flash (after the Start/Pause button (Départ/Pause) has been pressed). To set a delayed start, press the Time Delay button, and the light next to the button will come on together with the 3hr delay light. Pressing the button again will advance the delay setting to 6hr, the 3hr light goes out and the 6hr light is on. Articles that containing rubber or rubber-like materials or plastic film (pillows, cushions, or PVC rainwear), any other flammable articles or objects that contain flammable substances (towels soiled with hair spray). Glass fibres (certain types of draperies) Items which have been dry cleaned Items with the ITCL Code (see Special clothing items). These can be cleaned with special at-home dry cleaning products. Large bulky items (quilts, sleeping bags, pillows, cushions, large bedspreads etc). These expand when drying and would prevent airflow through the dryer. At the end of a drying cycle, cottons could still be damp if you grouped cottons and synthetics together. If this happens simply give them an additional short period of drying. Q Note: The last 10 minutes of any time set is the Cool Tumble, so allow for this when setting the time, as this period will not dry your laundry. Blankets and Bedspreads: acrylic items (Acilan, Courtelle, Orion, Dralon) must be dried with special care on LOW heat setting. Starched articles: do not dry these with non-starched items. Make sure that as much of the starch solution is removed from the load as possible before placing it in the dryer. Do not over-dry: the starch will become powdery and leave your clothing limp, which defeats the purpose of starch. Fabrics: items that are the same type of fabric but different textures and thicknesses may not have the same drying time. Quantity of laundry: single items or small loads may take longer to dry. [. . . ] The temperature setting is not ideal for the type of fabric you are drying (see Start and Programmes, and see Laundry). The correct drying time has not been selected for the load (see Laundry). Do not wait for the empty water signal, always check and empty the container before starting a new drying programme (see Maintenance). This is normal, the light flashes when the container is full. [. . . ]