User manual HOTPOINT ECOT6L 1051 EU B

[. . . ] Instructions for use WASHING MACHINE Contents GB English, 1 GB IT Italiano, 13 ES Español, 25 Installation, 2-3 Unpacking and levelling Connecting the electricity and water supplies The first wash cycle Technical data GR ÅëëçíéêÜ, 37 Care and maintenance, 4 Cutting off the water or electricity supply Cleaning the washing machine Caring for your appliance door and drum Cleaning the pump Checking the water inlet hose How to clean the detergent dispenser Precautions and tips, 5 General safety Disposal Saving energy and respecting the environment Description of the washing machine and starting a wash cycle, 6-7 ECOT6L 1051 Control panel Indicator lights How to open and shut the drum Starting a wash cycle Wash cycles, 8 Table of wash cycles Personalisation, 9 Setting the temperature Setting the spin speed Functions Detergents and laundry, 10 Detergent dispenser drawer Bleach cycle Preparing the laundry Garments requiring special care Load balancing system Troubleshooting, 11 Service, 12 1 Installation GB !Keep this instruction manual in a safe place for future reference. Should the appliance be sold, transferred or moved, make sure the instruction manual accompanies the washing machine to inform the new owner as to its operation and features. Read these instructions carefully: they contain vital information on installation, use and safety. [. . . ] Lid locked indicator light If this indicator light is on, the appliance door is locked to prevent it from being opened accidentally; to avoid any damage, wait for the indicator light to switch off (it will take about three minutes) before you open the appliance door. If the DELAY TIMER function is activated, the door cannot be opened; pause the machine by pressing the START/PAUSE button if you wish to open it. If the START/PAUSE indicator light (orange) flashes rapidly at the same time as the function indicator light, this indicates a problem has occurred (see “Troubleshooting”). GB B) Opening the drum (Soft opening): With one finger, push the button indicated in fig. 4): - close the drum fully by first shutting the front door followed by the rear one; - then ensure the hooks on the front door are perfectly housed within the seat of the rear door; - after the hooks have clicked into position, press both doors lightly downwards to make sure they do not come loose; - finally shut the external lid. Turn the washing machine on by pressing the ON/OFF button. All the indicator lights will turn on for a few seconds, then only the indicator lights relative to the selected programme settings will remain lit and the START/PAUSE indicator light will flash. Load the laundry, close the door and the lid. Set the WASH CYCLE knob to the desired programme. Set the spin speed (see “Personalisation”). Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit in a fixed manner, in green. To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle. At the end of the wash cycle the indicator light will switch on. The LID LOCKED indicator light will switch off, indicating that the door may be opened. Take out your laundry and leave the appliance door ajar to make sure the drum dries completely. Switch the washing machine off by pressing the ON/OFF button. How to open and to close the drum Fig. Load (Kg) Total water lt 67 65 39 39 29 51 27 34 Wash cycles Detergents Description of the wash cycle Fabric BlePrewash Wash softe- ach ner Energy consumption kWh 1, 92 1, 02 0, 85 0, 53 0, 08 0, 10 0, 07 0, 04 - GB Essentials cycles 1 Cotton + Prewash: extremely soiled whites. Mix 15’: to refresh lightly soiled garments quickly (not suitable for wool, silk and clothes which require washing by hand). 11 Cottons 12 Synthetics 13 Fast Wash Partials wash cycles A Rinse B Spin C Pump out  -  - The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected. 1) Test wash cycle in compliance with directive 1061/2010: set wash cycle 2 with a temperature of 60°C. [. . . ] Possible causes / Solutions: • The appliance is not plugged into the socket fully, or is not making contact. € The water inlet hose is not connected to the tap. • The START/PAUSE button has not been pressed. € The drain hose is not fitted at a height between 65 and 100 cm from the floor (see “Installation”). [. . . ]