User manual HOTPOINT FTGHL 641 D/IX/HA LP

[. . . ] FTGHL 641 D/IX/HA LPG FTGHG 641 D/HA(BK)LPG FTGHL 751 D/IX/HA LPG FTGHG 751 D/HA(BK)LPG Français Mode d’emploi TABLE DE CUISSON Sommaire Mode d’emploi, 1 Avertissements, 4 Assistance, 8 Description de l’appareil, 10 Installation, 26 Mise en marche et utilisation, 30 Précautions et conseils, 30 Nettoyage et entretien, 31 Anomalies et remèdes, 31 Italiano Español Istruzioni per l’uso PIANO Sommario Istruzioni per l’uso, 1 Avvertenze, 3 Assistenza, 8 Descrizione dell’apparecchio, 10 Installazione, 13 Avvio e utilizzo, 17 Precauzioni e consigli, 17 Manutenzione e cura, 18 Anomalie e rimedi, 18 Manual de instrucciones ENCIMERA Sumario Manual de instrucciones, 1 Advertencias, 4 Asistencia, 8 Descripción del aparato, 10 Instalación, 33 Puesta en funcionamiento y uso, 37 Precauciones y consejos, 37 Mantenimiento y cuidados, 38 Anomalías y soluciones, 38 English Portuges Operating Instructions HOB Contents Operating Instructions, 1 Warnings, 3 Assistance, 8 Description of the appliance, 10 Installation, 20 Start-up and use, 23 Precautions and tips, 23 Maintenance and care, 24 Troubleshooting, 24 Instruções para a utilização PLANO Índice Instruções para a utilização, 1 Advertências, 5 Assistência, 9 Descrição do aparelho, 11 Instalação, 40 Início e utilização, 44 Precauções e conselhos, 44 Manutenção e cuidados, 45 Anomalias e soluções, 45 Deutsch Ελλη ATTENZIONE: In caso di danneggiamento del piano in vetro: - spegnere immediatamente tutti i bruciatori e eventuali elementi riscaldanti elettrici e scollegare l’apparecchio dalla rete elettrica - non toccare la superfice dell’apparecchio Warnings WARNING: The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements. Children less than 8 years of age shall be kept away unless continuously supervised. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. [. . . ] Checking the tightness of the connection !When the installation process is complete, check the pipe fittings for leaks using a soapy solution. This procedure must be performed by a qualified technician authorised by the manufacturer. Once this procedure is finished, replace the old rating sticker with one indicating the new type of gas used. Stickers are available from any of our Service Centres. Should the gas pressure used be different (or vary slightly) from the recommended pressure, a suitable pressure regulator must be fitted to the inlet pipe (in order to comply with current national regulations). DATA PLATE Electrical see data plate connections This appliance conforms to the following European Economic Community directives: - 2006/95/EC dated 12/12/06 (Low Voltage) and subsequent amendments - 2004/108/EC dated 15/12/04 (Electromagnetic Compatibility) and subsequent amendments - 93/68/EEC dated 22/07/93 and subsequent amendments. The hob can only be installed above built-in ovens with a cooling ventilation system. Electrical connection Hobs equipped with a three-pole power supply cable are designed to operate with alternating current at the voltage and frequency indicated on the data plate (this is located on the lower part of the appliance). The earth wire in the cable has a green and yellow cover. If the appliance is to be installed above a built-in electric oven, the electrical connection of the hob and the oven must be carried out separately, both for electrical safety purposes and to make extracting the oven easier. Connecting the supply cable to the mains Install a standardised plug corresponding to the load indicated on the data plate. The appliance must be directly connected to the mains using an omnipolar circuit-breaker with a minimum contact opening of 3 mm installed between the appliance and the mains. The circuit-breaker must be suitable for the charge indicated and must comply with current electrical regulations (the earthing wire must not be interrupted by the circuit-breaker). The supply cable must not come into contact with surfaces with temperatures higher than 50°C. The installer must ensure that the correct electrical connection has been made and that it is compliant with safety regulations. Before connecting to the power supply, make sure that: • the appliance is earthed and the plug is compliant with the law. € the socket can withstand the maximum power of the appliance, which is indicated on the data plate. € the voltage is in the range between the values indicated on the data plate. € the socket is compatible with the plug of the appliance. If the socket is incompatible with the plug, ask an authorised technician to replace it. Once the appliance has been installed, the power supply cable and the electrical socket must be easily accessible. [. . . ] € There are draughts near the appliance. The flame dies in models with a safety device. Check to make sure that: • You pressed the knob all the way in. € You keep the knob pressed in long enough to activate the safety device. [. . . ]