User manual HOTPOINT GPN 64 CI RFH

[. . . ] мұны Пайдалану нұсқаулығы, 1 Ескертулер, 3 Көмек, 4 Құрылғы сипаттамасы, 5 Орнату, 21 Қосу және пайдалану, 26 Сақтандырулар мен кеңестер, 26 Жөндеу және күтім, 27 Ақаулықтарды жою, 27 English Operating Instructions HOB Contents Operating Instructions, 1 Warnings, 2 Assistance, 4 Description of the appliance, 5 Installation, 6 Start-up and use, 11 Precautions and tips, 11 Maintenance and care, 12 Troubleshooting, 12 Русскии Руководство по эксплуатации ВАРОЧНАЯ ПАНЕЛЬ Содержание Руководство по эксплуатации, 1 Предупреждения, 2 Сервисное обслуживание, 4 Описание из делия, 5 Установка, 13 Включение и эксплуатация, 18 Предосторожности и рекомендации, 18 Техническое обслуживание и уход, 19 Неисправности и методы их устранения, 19 CAUTION: the use of inappropriate hob guards can cause accidents. Warnings WARNING: The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements. Children less than 8 years of age shall be kept away unless continuously supervised. [. . . ] Gas connection The appliance should be connected to the main gas supply or to a gas cylinder in compliance with current national regulations. Before carrying out the connection, make sure the cooker is compatible with the gas supply you wish to 7 GB use. If this is not the case, follow the instructions indicated in the paragraph “Adapting to different types of gas. € When using liquid gas from a cylinder, install a pressure regulator which complies with current national regulations. Check that the pressure of the gas supply is consistent with the values indicated in Table 1 (“Burner and nozzle specifications”). This will ensure the safe operation and longevity of your appliance while maintaining efficient energy consumption. connection with a rigid pipe (copper or steel) !Connection to the gas system must be carried out in such a way as not to place any strain of any kind on the appliance. There is an adjustable L-shaped pipe fitting on the appliance supply ramp and this is fitted with a seal in order to prevent leaks. The seal must always be replaced after rotating the pipe fitting (seal provided with appliance). These pipes must be installed so that they are never longer than 2000 mm when fully extended. Once connection has been carried out, make sure that the flexible metal pipe does not touch any moving parts and is not compressed. Only use pipes and seals that comply with current national regulations. Checking the tightness of the connection !When the installation process is complete, check the pipe fittings for leaks using a soapy solution. Adapting to different types of gas To adapt the hob to a different type of gas other than default type (indicated on the rating plate at the base of the hob or on the packaging), the burner nozzles should be replaced as follows: 1. Remove the hob grids and slide the burners off their seats. Unscrew the nozzles using a 7 mm socket spanner, and replace them with nozzles for the new type of gas (see table 1 “Burner and nozzle characteristics”). Reassemble the parts following the above procedure in the reverse order. Once this procedure is finished, replace the old rating sticker with one indicating the new type of gas used. Sticker are available from any of our Service Centres. replacing the Triple ring burner nozzles 1. [. . . ] € You keep the knob pressed in long enough to activate the safety device. € The gas holes are not blocked in the area corresponding to the safety device. The burner does not remain lit when set to minimum. Check to make sure that: • The gas holes are not blocked. [. . . ]