User manual HOTPOINT HLB 9.8 ASH X/HA

[. . . ] If you sell, transfer or move the unit to another location, make sure to keep the manual with the product. Read the instructions carefully - they contain important installation, user and safety information. Do not tamper with the electrical or mechanical equipment of the product or its exhaust ducts. € Si consiglia di pulire frequentemente il prodotto, sia internamente che General safety information esternamente (ALMENO UNA VOLTA • The distance between the cookware support surface on top of the cooking AL MESE, rispettare comunque quanto appliance and the lowest part of the espressamente indicato nelle istruzioni cooker hood must be at least: di manutenzione riportate in questo 65 cm if the hood is installed over a gas manuale). [. . . ] The time for cleaning/replacement is signalled by the flashing of the coloured LED associated to the filter (white for antigrease filters, red for odour filter). The LED is turned off by pressing the T7 button after cleaning/replacing the filters. T8 lights ON/OFF It turns the work lights of the hood on and off. Hood configuration The configuration menu is accessed with the product off by pressing T5 and T6 for 6 seconds. T7 turns on at this point to indicate the type of installation through two colours of the LED: white for extractor installation (default), red for filtering installation. The installation type can be changed by pressing T7 cyclically with the consequent alternation of the LED colours. T1 motor ON/OFF When the button is pressed with the hood off, the first speed is set. When the button is pressed during operation, the hood switches OFF. T2 Speed – When the button is pressed the hood switches to the previous speed. T3 Speed + If the hood is set to speed 3, the intensive speed activates when this button is pressed The setting is limited by time; when it elapses the hood goes back to the speed set previously. T4 Timer “–” Set a time to turn OFF the hood with the timer; if the timer is set and the speed is subsequently changed by pressing T2, T3 or T4, the timer is deactivated. press T4 to decrease the timer by 5 minutes. T5 Timer “+” When the button is pressed for the first time, the timer is set to 5 minutes; this value is increased by 5 additional minutes every time the button is pressed after that. T6 lights ON/OFF It turns the work lights of the hood on and off I1 D1 D2 I5 I2 D1: DGT Speed D2: Assembly of 2 DGT Time I1: Grease Filter Indicator I2: Carbon Filter Indicator I4: Menu Indicator I5: Timer Indicator I4 31 GB Antigrease and odour filter signal The antigrease (A) and/or odour (B) filters need cleaning/ replacing after a certain number of hours of use (the latter for filtering hoods only). The indicator light I1 on indicates that the antigrease filter is saturated, while the indicator light I2 on indicates that the odour filter is saturated (for hoods in filtering mode only). Press T5 + T4 for 3 seconds with the hood on to reset the counter. Hood type setting The hood can be set to the ventilation (default) or filtering mode. To change the setting proceed as follows: • with the hood OFF, the menu is accessed by pressing the T4 e T5 buttons for a prolonged time; this is signalled by a sound emitted by the hood and by the I4 icon lighting up and the writing C1-0 appearing on the display; • use the buttons T4 and T5 to go through the menu. Use T4 to go through the various menu items (C1, C2, C3, C4, etc) and T5 to select them (0, 1 or 0, 1, 2); • to set the hood type, access the menu, select the item C6 with T4 and set the value 0 with T5 to set the hood on ventilation mode or 1 for the filtering mode. Hood off The hood can be turned off manually by pressing the T1 button (ON/OFF). If the hood stays on in manual mode, it turns off automatically after a certain “safety” time. If the timer is set, the hood turns off automatically when the set time runs out. [. . . ] Assembly: Secure the activated-carbon filter first in the back using the hood's metal tabs and then in the front by pressing the two levers. Hook the front panel of the box to the tabs at the bottom first and then push it in the upper part of the panel until the pivots wedge in. B To carry out this operation, the use of gloves and a ladder is advised. * Only available in certain models 34 Replacing the bulbs Disconnect the unit from the mains and remove the grease filter. [. . . ]