User manual HOTPOINT HNB 9.8 ADI X

[. . . ] € It is not intended for use by children or persons with sensory or mental disability and lack of experience or familiarity, except under the supervision or instruction of a person responsible for their safety. € Make sure children do not play with the unit. € Never operate the unit without its grease filter installed!€ NEVER use the hood as a support, unless expressly instructed to do so. [. . . ] The air being exhausted may not be exhausted into a wall cavity unless the cavity in question is specifically intended for this purpose. Equip the room with air intakes to prevent the hood creating suction pressure in the interior (this must not exceed 0. The manufacturer is not liable for any consequences of failure to observe these instructions. Of exhaust tube (cm) 15/12 15/12 Bulb draw (W) Total draw (W) 2 x 20 2 x 20 240 290 Power Halogen 25 W Halogen 20 W 2 x 25 W 2 x 20 W Voltage 230 V 12 V Cap G9 G4 Dimensions L40xØ14 L30xØ10 LED * Risk Group 1 according to Standard EN 62471 Filter or ducted?If you wish to use it as a filter unit, you must install the proper ACCESSORY KIT. Note: If supplied with the hood, the accessory active charcoal filter unit may already be installed. Instructions for transforming the hood from the ducted to the filter version are given in this manual (see “Filter version”). The hoods are conforming to the following EC Directives: • “Low voltage” Directive 2006/95/EC (12-12-2006) • “EMC” Directive 2004/108/EC (15-12-2004) * Only available in certain models 15 GB TBOX controls Models with mechanical keypad (Only available in certain models) The T2 icon flashes to indicate that the grease filter is saturated, while T3 flashes to indicate that the odour filter is saturated, and if both are flashing then both filters are saturated. You must then clean/replace the grease filter (A) or odour filter (B) or both, accordingly (see “Maintenance and care”). To reset the filter counter: Hold down T4 for three seconds while the hood is on. The warning led flashes three times, then returns to its normal mode If both filter warnings are active at the same time, you must reset each separately. The first sequence resets the grease filter, while the second sequence resets the odour filter. Hood configuration: To set the operating mode of the hood, hold down T5 for 6 seconds while the product is off. Icons T2 or T3 will light up to show the type of installation: T2 ventilation, T3 filtering. You can change the type of installation by pressing T4 cyclically. to save the new configuration press T1 individually. T1 T2 T3 T4 T5 T1 Motor reset Pressing the button while the hood is in operation turns it OFF. T2 Speed 1 Pressing the button sets the hood to speed 1. T3 Speed 2 Pressing the button sets the hood to speed 2. T4 Speed 3 Pressing the button sets the hood to speed 3. 8 ADI X B Models with soft button keypad (Only available in certain models) B T1 T2 T3 T4 T5 T6 T1 T2 T3 T4 T5 T6 T1 Motor reset Pressing the button while the hood is in operation turns it OFF. T2 Speed 1 Pressing the button sets the hood to speed 1. [. . . ] You can change the type of installation by pressing T4. To quit configuration mode, press T1 once; this switches the unit off and saves the last displayed setting. Before cleaning or servicing the unit, disconnect it from the mains by pulling the power plug or disconnecting the main circuit breaker. First cleaning • Remove the protective film • Clean with a damp sponge and a little neutral soap • Rinse off with a damp cloth • Dry with a soft cloth; if the hood is stainless steel, dry along the metal's grain Assembly: Secure the activated-carbon filter first in the back using the hood's metal tabs and then in the front by pressing the two levers. [. . . ]