User manual HOTPOINT HNP 9.6 AB X/HA

[. . . ] If you sell, transfer or move the unit to another location, make sure to keep the manual with the product. Read the instructions carefully - they contain important installation, user and safety information. Do not tamper with the electrical or mechanical equipment of the product or its exhaust ducts. Ceiling, which must be strong enough to support the weight of the unit. [. . . ] The manufacturer is not liable for any consequences of failure to observe these instructions. 5 CM (AN)/HA Bulb (V) Bulb draw (W) Total draw (W) Halogen 2 x 25 160 Model code HNP 6. 5S CM (AN)/HA Bulb (V) Bulb draw (W) Total draw (W) Halogen 2 x 25 195 Model code HNP 6. 6 CM (OW)/HA Bulb (V) Bulb draw (W) Total draw (W) Filter or ducted?If you wish to use it as a filter unit, you must install the proper ACCESSORY KIT. Note: If supplied with the hood, the accessory active charcoal filter unit may already be installed. Instructions for transforming the hood from the ducted to the filter version are given in this manual (see “Filter version”). 8 CM (AN)/HA Bulb (V) Halogen Bulb draw (W) Total draw (W) 2 x 25 300 35 GB Halogen 25 W Halogen 20 W Power 2 x 25 W 2 x 20 W Voltage 230 V 12 V Cap G9 G4 Dimensions L40xØ14 L30xØ10 Models with soft button keypad HNP 9. 6 AB X/HA B LED * Risk Group 1 according to Standard EN 62471 T1 T2 T3 T4 T5 T6 The hoods are conforming to the following EC Directives: • “Low voltage” Directive 2006/95/EC (12-12-2006) • “EMC” Directive 2004/108/EC (15-12-2004) T1 Motor reset Pressing the button while the hood is in operation turns it OFF. T2 Speed 1 Pressing the button sets the hood to speed 1. 5S CM (AN)/HA T3 Speed 2 Pressing the button sets the hood to speed 2. T4 Speed 3 Pressing the button sets the hood to speed 3. T5 Booster Pressing the button sets the hood to high speed. After 5 minutes, the hood returns to the previous speed; pressing a speed button (T2, T3 or T4) quits booster mode and sets the selected speed. T6 Lights ON/OFF Grease/odour filter warnings The T2 icon flashes to indicate that the grease filter is saturated, while T3 flashes to indicate that the odour filter is saturated, and if both are flashing then both filters are saturated. You must then clean/replace the grease filter (A) or odour filter (B) or both, accordingly (see “Maintenance and care”). To reset the filter counter: Hold down T4 for three seconds while the hood is on. The warning led flashes three times, then returns to its normal mode If both filter warnings are active at the same time, you must reset each separately. The first sequence resets the grease filter, while the second sequence resets the odour filter. Hood configuration: To set the operating mode of the hood, hold down T5 for 6 seconds while the product is off. Icons T2 or T3 will light up to show the type of installation: T2 ventilation, T3 filtering. You can change the type of installation by pressing T4 cyclically. [. . . ] Use a damp cloth and a neutral liquid detergent with lukewarm water. do not use abrasive or corrosive products. Warning: Failure to observe the hood cleaning and filter cleaning/replacement instructions can result in fires. The manufacturer is not liable for any damage to the motor or fires caused by incorrect care or failure to follow the above instructions. [. . . ]