User manual HOTPOINT KOT 7424 ID

[. . . ] 13 Operating Instructions HOB Contents IT Italiano, 1 GB GB English, 14 FR Français, 27 Installation, 15-17 Positioning Connecting the hob Disposal ES Espanol, 40 PT Portuges, 53 Description of the appliance, 18-19 Control panel Cooking zone description Start-up and use, 20-23 KOT 7424 ID/HA KOT 7424 ID 400/HA Turning on the hob Turning off the hob The booster Programmed settings Positioning the cookeye® device How to turn on the cookeye® device How to use the cookeye® device Programming in cookeye® mode How to turn off the cookeye® device The safety devices, 24 Pan recognition What cookware to use Acoustic signal Safety cut out Overheating protection device Precautions and tips, 25 Practical advice on using the appliance General safety Care and maintenance, 26 Switching the appliance off Cleaning the appliance Cookeye® care Disassembling the hob Installation !Before operating your new appliance please read this instruction booklet carefully. It contains important information concerning the safe operation, installation and maintenance of the appliance. Please keep these operating instructions for future reference. [. . . ] Option 2: If you press both the top and lower part of the cooking zone control key simultaneously, the beeping stops, as does the temperature adjustment. The hob returns to manual mode, mode and you are free to modify the temperature setting as necessary. Note Should you wish to use two cookeye® devices, we recommend you start one device at a time in order to avoid any confusion in correspondence with the relevant controls. B e Note If you fail to intervene, the hob continues its automatic temperature adjustment and continues to beep. If you fail to intervene within the next 10 minutes, the cooking zone is turned off. In any case, the flashing programmed setting indicator light on the power level display indicates a pre-heating phase, whereas a fixed lit indicator light indicates the dish has reached the desired temperature. 22 Programming in cookeye® mode How to turn off the cookeye® device At any time, you can cancel a programmed setting in cookeye® mode: • press both the lower and top parts of the cooking zone control key simultaneously the six simultaneously: programmed setting indicator lights on the power level display begin to flash, • press again both the lower and top parts of the cooking zone control key simultaneously: the power level display turns off and the cooking zone goes back to normal mode, • to go back to cookeye® mode, press these keys again. GB To turn off the cookeye® device, press the red button for 3 seconds and the cooking zone will go back to normal mode. If the cookeye® device is switched off involuntarily, the hob will signal this fault: all the programmed setting symbols will flash and the hob will beep. press the cookeye® button to re-enable it. If you fail to do anything about it, the cooking zone power will begin to drop to a level immediately beneath the one which would have allowed the temperature to be maintained at a suitable level. After one minute, the cooking zone is turned off if it has not received any signals from the cookeye® device. You can programme a cooking time in cookeye® mode, just as you would in normal mode. Proceed in an identical manner: key to access the programming. Set Press the the desired cooking time by pressing the lower and/ or top part of the cooking zone control key. Key again to confirm the Press the programming. The countdown begins after the pre-heating phase (the cooking time display flashes) • and after you have acted on the keys • or following the detection that something has been added to the pan (pasta to boiling water for example). It is however possible to start the countdown by pressing the timer key for 3 seconds; in this case, no acoustic alarm is sounded at the end of preheating. Note The hob allows you to programme several cooking zones simultaneously, whether they are in normal mode or in cookeye® mode. 23 The safety devices GB Pan recognition Acoustic signal Each induction cooking zone is fitted with a pan recognition device. The cooking zone only provides heat in the presence of a pan which is suitable for the cooking zone. A blinking pan recognition indicator could signal: • that the pan is made of unsuitable material, which is not ferromagnetic, • that the diameter of the pan is too small, • that the pan has been removed. [. . . ] • Never clean the cookeye® device under running water or in your dishwasher. • Do not use the cookeye® device with a lid on the pan or a kitchen utensil inside it (ladle, spoon, whip, etc. • Prevent any draughts of air from “chasing” the steam produced by the pan towards the lens on cookeye® device as this could disrupt the “view” of the latter. Stainless steel frame * Stainless steel can be marked by hard water which has been left on the surface for a long time, or by cleaning products containing phosphorus. [. . . ]