User manual HOTPOINT LIQ 700 TI PLUS

[. . . ] 12 Instruction booklet DISHWASHER Contents Installation, 14-15 Positioning and levelling Connecting the water and electricity supplies Technical data EN English, 13 EN Description of the appliance, 16 Overall view Control panel Loading the racks, 17 Lower rack Cutlery basket Upper rack Start-up and use, 18 LI 680 PLUS LI 700 PLUS LIQ 700 PLUS Starting the dishwasher Loading the detergent Washing options Wash cycles, 19 Wash cycle table Rinse aid and refined salt, Loading the rinse aid Loading the refined salt 20 Care and maintenance, 21 Shutting off the water and electricity supplies Cleaning the dishwasher Preventing unpleasant odours Cleaning the sprayer arms Cleaning the filters Leaving the machine unused for extended periods Precautions and advice, 22 General safety Disposal Saving energy and respecting the environment Troubleshooting, Assistance, 24 23 Before calling for Assistance Installation EN  Keep this instruction manual in a safe place for future reference. If the appliance is sold, given away or moved, please ensure the manual is kept with the machine, so that the new owner may benefit from the advice contained within it.  Please read this instruction manual carefully: it contains important information regarding the safe installation, use and maintenance of the appliance.  If the appliance must be moved at any time, keep it in an upright position; if absolutely necessary, it may be tilted onto its back. [. . . ] Loading the detergent A successful wash also depends on the correct amount of detergent being used, as recommended by the manufacturer. Exceeding the recommended amount does not result in a more effective wash and pollutes the environment. Pour in the detergent after consulting the Wash cycle table: 18 Wash cycles Wash cycle table  Ariston dishwashers are fitted with an automatic filter cleaning system that may increase the cycle duration.  AUTO WASH CYCLES: This model of dishwasher is equipped with a special sensor which can be used to assess the level of soiling and automatically select the most efficient and economic wash cycle accordingly. Position the funnel provided correctly (see figure) and fill the salt dispenser up to the edges (approximately 2 kg); it is normal for a little water to leak out. Remove the funnel, wipe away any salt residue from the thread and screw the cap on tightly, so that detergent does not leak into the dispenser during the wash cycle (this could damage the water softening system beyond repair).  When salt has been added, run a wash cycle immediately, without crockery, in order to remove any salt solution that has leaked out and to avoid corrosion. Adjusting the amount of salt* It is possible to adjust the amount of salt used according to the hardness of the water in your area (this information is available from your local water board). Turn the arrow on the neck of the dispenser (see figure) towards the + or - symbols, using the table below as a guide. Loading the rinse aid Rinse aid makes it easier for the crockery to dry, as water runs off surfaces more readily and therefore does not leave streaks or marks. The rinse aid dispenser should be filled: • whenever the indicator light (H) signals that it is empty. Illuminated light: add rinse aid; unlit light: there is no shortage of rinse aid in the dispenser. €¢ when the LOW RINSE AID* indicator light on the panel flashes; 1. Open the dispenser by H turning the lid (G) in an anticlockwise direction. Pour in the rinse aid, making sure it does not F overflow from the dispenser. If this happens, G clean the spill immediately with a sponge. Adjusting the amount of rinse aid If you are not completely satisfied with the washing or drying results, you may adjust the quantity of rinse aid used. Use a screwdriver to turn the dosage adjuster to one of the 6 pre-set positions (the default position is set to 4): • if there are white streaks on the crockery, set the adjuster to a lower number (1-3). €¢ if drops of water remain on the crockery or there are limescale marks present after the cycle has finished, set the adjuster to a higher number (4-6).  If you are using multi-functional tablets (2-in-1, 3-in-1, 4-in-1, etc. ) and you wish to further improve the drying performance of the appliance, fill the dispenser and set the dosage adjuster to 2. Loading the refined salt In order to obtain the best possible results from a wash cycle, make sure that the dispenser is never empty. [. . . ] • The rinse aid dispenser setting is not high enough. €¢ A wash cycle without a drying programme has been selected. €¢ • • • • The racks are overloaded (see Loading the racks). The crockery has not been arranged well. [. . . ]