User manual HOTPOINT LL 6066 SK

[. . . ] Instruction booklet DISHWASHER EN English, 1 NO Norsk, 13 SV Svenka, 25 Contents Installation, 2-3 Positioning and levelling Connecting the water and electricity supplies Technical data DA Dansk, 37 FI Suomi, 49 Description of the appliance, 4 Overall view Control panel Loading the racks, 5 Lower rack Cutlery basket Upper rack Start-up and use, Starting the dishwasher Loading the detergent Washing options 6 LL 6066 Wash cycles, 7 Wash cycle table Rinse aid and refined salt, Loading the rinse aid Loading the refined salt 8 Care and maintenance, 9 Shutting off the water and electricity supplies Cleaning the dishwasher Preventing unpleasant odours Cleaning the sprayer arms Cleaning the filters Leaving the machine unused for extended periods Precautions and advice, 10 General safety Disposal Saving energy and respecting the environment Troubleshooting, Assistance, 12 11 Before calling for Assistance Installation EN  Keep this instruction manual in a safe place for future reference. If the appliance is sold, given away or moved, please ensure the manual is kept with the machine, so that the new owner may benefit from the advice contained within it.  Please read this instruction manual carefully: it contains important information regarding the safe installation, use and maintenance of the appliance.  If the appliance must be moved at any time, keep it in an upright position; if absolutely necessary, it may be tilted onto its back. [. . . ] Turn the arrow on the neck of the dispenser (see figure) towards the + or - symbols, using the table below as a guide. Loading the rinse aid Rinse aid makes it easier for the crockery to dry, as water runs off surfaces more readily and therefore does not leave streaks or marks. The rinse aid dispenser should be filled: • whenever the indicator light (H) signals that it is empty. Illuminated light: add rinse aid; unlit light: there is no shortage of rinse aid in the dispenser. € when the LOW RINSE AID* indicator light on the panel flashes; 1. Open the dispenser by turning the lid (G) in an H anticlockwise direction. Pour in the rinse aid, making sure it does not overflow from the F dispenser. If this happens, G clean the spill immediately with a sponge. NEVER pour the rinse aid directly into the appliance tub. Adjusting the amount of rinse aid If you are not completely satisfied with the washing or drying results, you may adjust the quantity of rinse aid used. Use a screwdriver to turn the dosage adjuster to one of the 6 pre-set positions (the default position is set to 4): • if there are bluish streaks on the crockery, set the adjuster to a lower number (1-3). € if drops of water remain on the crockery or there are limescale marks present after the cycle has finished, set the adjuster to a higher number (4-6).  If you are using multi-functional tablets (2-in-1, 3-in-1, 4-in-1, etc. ) and you wish to further improve the drying performance of the appliance, fill the dispenser and set the dosage adjuster to 2. Loading the refined salt In order to obtain the best possible results from a wash cycle, make sure that the dispenser is never empty. Refined salt removes limescale from the water, thus avoiding the formation of deposits on crockery. The salt dispenser is located in the lower 8 The default setting of the water softening system is +. - If using multi-functional tablets (2-in-1 , 3-in-1 , 4-in-1 , etc. ) fill the salt dispenser and set the adjuster to -; if the hardness of the water is greater than 60°fH, set it to +. Care and maintenance Shutting off the water and electricity supplies • Turn off the water tap after every wash cycle to avoid leaks. € Remove the plug from the socket when cleaning the machine and when carrying out maintenance work. Cleaning the filters The filters remove food residue from the water used in the wash cycle: to obtain the best results from each wash, they should be cleaned. [. . . ] If the alarm continues, shut off the water tap to eliminate the risk of flooding, remove t he plug from the electrical socket and call Assistance. possible causes / Solutions: Tap shut -off alarm. (several short beeps are emitted) * Only available in selected models. (the second and third WASH CYCLE indicator lights flash, beginning from the right). [. . . ]