User manual HOTPOINT LVR 645 A AN

[. . . ] 12 Instruction booklet DISHWASHER Contents Installation, 14-15 Positioning and levelling Connecting the water and electricity supplies Technical data EN English, 13 Description of the appliance, 16 Overall view Control panel Loading the racks, 17 Lower rack Cutlery basket Upper rack Start-up and use, 18 LV 625 LV 645 A LVR 645 A Starting the dishwasher Loading the detergent Washing options Wash cycles, 19 Wash cycle table Rinse aid and refined salt, Loading the rinse aid Loading the refined salt 20 Care and maintenance, 21 Shutting off the water and electricity supplies Cleaning the dishwasher Preventing unpleasant odours Cleaning the sprayer arms Cleaning the filters Leaving the machine unused for extended periods Precautions and advice, 22 General safety Disposal Saving energy and respecting the environment Troubleshooting, Assistance, 24 23 Before calling for Assistance Installation EN  Keep this instruction manual in a safe place for future reference. If the appliance is sold, given away or moved, please ensure the manual is kept with the machine, so that the new owner may benefit from the advice contained within it.  Please read this instruction manual carefully: it contains important information regarding the safe installation, use and maintenance of the appliance.  If the appliance must be moved at any time, keep it in an upright position; if absolutely necessary, it may be tilted onto its back. [. . . ] Economic and fast cycle to be used for slightly dirty dishes. Rapid Preliminary wash cycle for dishes while the load is awaiting completion with the dishes from the next meal. Special cycle to be used for more delicate items which are sensitive to high temperatures. Rinse and drying cycle for dishes that are seldom used and are only dusty. Turn the arrow on the neck of the dispenser (see figure) towards the + or - symbols, using the table below as a guide. Loading the rinse aid Rinse aid makes it easier for the crockery to dry, as water runs off surfaces more readily and therefore does not leave streaks or marks. The rinse aid dispenser should be filled: • whenever the indicator light (H) signals that it is empty. Illuminated light: add rinse aid; unlit light: there is no shortage of rinse aid in the dispenser. €¢ when the LOW RINSE AID* indicator light on the panel flashes; 1. Open the dispenser by turning the lid (G) in an H anticlockwise direction. Pour in the rinse aid, making sure it does not overflow from the F dispenser. If this happens, G clean the spill immediately with a sponge. NEVER pour the rinse aid directly into the appliance tub. Adjusting the amount of rinse aid If you are not completely satisfied with the washing or drying results, you may adjust the quantity of rinse aid used. Use a screwdriver to turn the dosage adjuster to one of the 6 pre-set positions (the default position is set to 4): • if there are bluish streaks on the crockery, set the adjuster to a lower number (1-3). €¢ if drops of water remain on the crockery or there are limescale marks present after the cycle has finished, set the adjuster to a higher number (4-6).  If you are using multi-functional tablets (2-in-1, 3-in-1, 4-in-1, etc. ) and you wish to further improve the drying performance of the appliance, fill the dispenser and set the dosage adjuster to 2. Loading the refined salt In order to obtain the best possible results from a wash cycle, make sure that the dispenser is never empty. Refined salt removes limescale from the water, thus avoiding the formation of deposits on crockery. The salt dispenser is located in the lower 20 The default setting of the water softening system is +. - If using multi-functional tablets (2-in-1 , 3-in-1 , 4-in-1 , etc. [. . . ] ╠The crockery has not been arranged well. • The sprayer arms cannot move freely. • The wash cycle is too gentle (see Wash cycles). • The detergent has not been measured out correctly or it is not suited to the type of wash cycle (see Start-up and use ). [. . . ]