User manual HOTPOINT LZ 705 IX EXTRA

[. . . ] 12 Instruction booklet DISHWASHER EN English, 13 Contents Installation, 14-15 Positioning and levelling Connecting the water and electricity supplies Technical data Description of the appliance, 16 Overall view Control panel Loading the racks, 17 Lower rack Cutlery basket Upper rack Start-up and use, LZ 705 EXTRA Starting the dishwasher Loading the detergent Washing options 18 Wash cycles, 19 Wash cycle table Rinse aid and refined salt, Loading the rinse aid Loading the refined salt 20 Care and maintenance, 21 Shutting off the water and electricity supplies Cleaning the dishwasher Preventing unpleasant odours Cleaning the sprayer arms Cleaning the filters Leaving the machine unused for extended periods Precautions and advice, 22 General safety Disposal Saving energy and respecting the environment Troubleshooting, Assistance, 24 23 Before calling for Assistance Installation EN  Keep this instruction manual in a safe place for future reference. If the appliance is sold, given away or moved, please ensure the manual is kept with the machine, so that the new owner may benefit from the advice contained within it.  Please read this instruction manual carefully: it contains important information regarding the safe installation, use and maintenance of the appliance.  If the appliance must be moved at any time, keep it in an upright position; if absolutely necessary, it may be tilted onto its back. [. . . ] Exceeding the recommended amount does not result in a more effective wash and pollutes the environment.  To obtain the best results from each washing and drying cycle, powder detergent, rinse aid liquid and salt should be used. ) it is not necessary to add rinse aid; however, we recommend that you add salt, especially if you live in an area where the water is hard or very hard. If you do not add salt or rinse aid, the LOW SALT* and LOW RINSE AID* indicator lights will flash continuously. The cap of the salt dispenser; when the LOW SALT* indicator light on the panel flashes; if your machine is not equipped with an indicator light or a green float: approximately every 30 wash cycles; • • Loading the rinse aid Rinse aid makes it easier for the crockery to dry, as water runs off surfaces more readily and therefore does not leave streaks or marks. The rinse aid dispenser should be filled: • whenever the indicator light (H) signals that it is empty. Illuminated light: add rinse aid; unlit light: there is no shortage of rinse aid in the dispenser. €¢ when the LOW RINSE AID* indicator light on the panel flashes; 1. Open the dispenser by turning the lid (G) in an H anticlockwise direction. Pour in the rinse aid, making sure it does not overflow from the dispenser. If this happens, F clean the spill immediately with a sponge. NEVER pour the rinse aid directly into the appliance tub. Remove the lower rack and unscrew the cap of the dispenser (in an anti-clockwise direction). For the first wash cycle only: fill the dispenser up to the edges with water. Position the funnel provided correctly (see figure) and fill the salt dispenser up to the edges (approximately 2 kg); it is normal for a little water to leak out. Remove the funnel, wipe away any salt residue from the thread and screw the cap on tightly, so that detergent does not leak into the dispenser during the wash cycle (this could damage the water softening system beyond repair).  When salt has been added, run a wash cycle immediately, without crockery, in order to remove any salt solution that has leaked out and to avoid corrosion. Adjusting the amount of salt* It is possible to adjust the amount of salt used according to the hardness of the water in your area (this information is available from your local water board). Turn the arrow on the neck of the dispenser (see figure) towards the + or symbols, using the table below as a guide. Adjusting the amount of rinse aid If you are not completely satisfied with the washing or drying results, you may adjust the quantity of rinse aid used. Use a screwdriver to turn the dosage adjuster to one of the 6 pre-set positions (the default position is set to 4): • if there are bluish streaks on the crockery, set the adjuster to a lower number (1-3). €¢ if drops of water remain on the crockery or there are limescale marks present after the cycle has finished, set the adjuster to a higher number (4-6). [. . . ] • A wash cycle without a drying programme has been selected. • The racks are overloaded (see Loading the racks). ╠The crockery has not been arranged well. • The sprayer arms cannot move freely. [. . . ]