User manual HOTPOINT PC 631 X

[. . . ] Operating Instructions HOB Contents Installation, 2-5 GB English, 1 GB FR Français, 12 ES Español, 25 Positioning Electrical connection Gas connection Burner and nozzle specifications PT Português, 37 FA AR Description of the appliance, 6 Overall view Start-up and use, 7-8 Practical advice on using the burners Practical advice on using the electric hotplate Precautions and tips, 9 General safety Disposal PC 631 X PC 631 N X PC 640 X PC 640 N X PC 640 N PC 640 N T GH PC 640 T X PC 640 T PC 730 RT GH PC 720 RTX PC 730 RTX PC 750 T X Maintenance and care, 10 Switching the appliance off Cleaning the appliance Gas tap maintenance Data plate Troubleshooting, 11 1 Installation !Before operating your new appliance please read this instruction booklet carefully. It contains important information for safe use, installation and care of the appliance. Please keep these operating instructions for future reference. [. . . ] Remove the pan supports and lift the burners out of their housing. The burner consists of two separate parts (see pictures). Unscrew the nozzles using a 7 mm socket spanner. Replace the nozzles with models that are configured for use with the new type of gas (see Table 1). The two nozzles have the same hole diameter. Replace all the components by completing the above operations in reverse order. € Adjusting the burners’ primary air : Does not require adjusting. • Setting the burners to minimum: 1. Remove the knob and adjust the adjustment screw, which is positioned in or next to the tap pin, until the flame is small but steady. Having adjusted the flame to the required low setting, while the burner is alight, quickly change the position of the knob from minimum to maximum and vice versa several times, checking that the flame does not go out. Some appliances have a safety device (thermocouple) fitted. If the device fails to work when the burners are set to the low flame setting, increase this low flame setting using the adjusting screw. Once the adjustment has been made, replace the seals on the by-passes using sealing wax or a similar substance. If the appliance is connected to liquid gas, the regulation screw must be fastened as tightly as possible. Once this procedure is finished, replace the old rating sticker with one indicating the new type of gas used. Stickers are available from any of our Service Centres. Should the gas pressure used be different (or vary slightly) from the recommended pressure, a suitable pressure regulator must be fitted to the inlet pipe (in order to comply with current national regulations). 78 MJ/m³ A R S Ø145 R A S S RR A TC S PC 631 X PC 631 N X PC 640 X PC 640 N X PC 640 N PC 640 T X PC 640 T PC 640 N T S DC TC DC TC RR TC A S S PC 730 RT GH PC 730 RT X PC 720 RT X PC 750 T X 5 Description of the appliance GB Overall view GAS BURNERS ELECTRIC HOTPLATE* Support Grid for COOKWARE Control Knobs for GAS BURNERS and ELECTRIC HOTPLATE* Indicator Light for ELECTRIC HOTPLATE* Support Grid for COOKWARE GAS BURNERS Control Knobs for GAS BURNERS SAFETY DEVICES * Ignition for GAS BURNERS * • The INDICATOR LIGHT FOR ELECTRIC HOTPLATES* switches on whenever the selector knob is moved from the ‘off’ position. • GAS BURNERS differ in size and power. Use the diameter of the cookware to choose the most appropriate burner to cook with. € Control Knobs for GAS BURNERS and ELECTRIC HOTPLATES * adjust the power or the size of the flame. • GAS BURNER ignition* enables a specific burner to be lit automatically. [. . . ] € The electric hotplates should be cleaned with a damp cloth and lubricated with a little oil while still warm. € Stainless steel can be marked by hard water that has been left on the surface for a long time, or by aggressive detergents containing phosphorus. After cleaning, rinse and dry any remaining drops of water. DATA PLATE Electrical see data plate connections This appliance conforms to the following European Economic Community directives: - 2006/95/EEC dated 12/12/06 (Low Voltage) and subsequent amendments - 2004/108/EEC dated 15/12/04 (Electromagnetic Compatibility) and subsequent amendments - 93/68/EEC dated 22/07/93 and subsequent amendments. [. . . ]