User manual HOTPOINT PCN 752 T/IX/HAR

[. . . ] PCN 752 T/IX/HAR Français Mode d’emploi TABLE DE CUISSON Sommaire Mode d’emploi, 1 Avertissements, 3 Assistance, 4 Description de l’appareil, 5 Installation, 18 Mise en marche et utilisation, 22 Précautions et conseils, 22 Nettoyage et entretien, 23 Anomalies et remèdes, 23 Italiano Istruzioni per l’uso PIANO Sommario Istruzioni per l’uso, 1 Avvertenze, 2 Assistenza, 4 Descrizione dell’apparecchio, 5 Installazione, 6 Avvio e utilizzo, 10 Precauzioni e consigli, 10 Manutenzione e cura, 11 Anomalie e rimedi, 11 ‫تعليمات التشغيل‬ ‫المحتويات‬ ‫رف تسخين‬ 1،‫تعليمات التشغيل‬ 2،‫تحذيرات‬ 4،‫المساعدة‬ 5،‫وصف الجهاز‬ 25 ،‫التركيب‬ 26،‫بدء التشغيل واالستخدام‬ 26 ،‫وسائل الحذر والنصائح‬ 26 ،‫الصيانة والعناية‬ 28 ،‫استكشاف المشاكل وحلها‬ English Operating Instructions HOB Contents Operating Instructions, 1 Warnings, 2 Assistance, 4 Description of the appliance, 5 Installation, 12 Start-up and use, 16 Precautions and tips, 16 Maintenance and care, 17 Troubleshooting, 17 Avvertenze ATTENZIONE: Questo apparecchio e le sue parti accessibili diventano molto caldi durante l’uso. Warnings WARNING: The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements. Children less than 8 years of age shall be kept away unless continuously supervised. [. . . ] Remove the hob grids and slide the burners off their seats. Unscrew the nozzles using a 7 mm socket spanner, and replace them with nozzles for the new type of gas (see table 1 “Burner and nozzle characteristics”). Reassemble the parts following the above procedure in the reverse order. Once this procedure is finished, replace the old rating sticker with one indicating the new type of gas used. Sticker are available from any of our Service Centres. replacing the Triple ring burner nozzles 1. Remove the pan supports and lift the burners out of their housing. The burner consists of two separate parts (see pictures). Unscrew the nozzles using a 7 mm socket spanner. Replace the nozzles with models that are configured for use with the new type of gas (see Table 1). The two nozzles have the same hole diameter. Electrical connection Hobs equipped with a three-pole power supply cable are designed to operate with alternating current at the voltage and frequency indicated on the data plate (this is located on the lower part of the appliance). The earth wire in the cable has a green and yellow cover. If the appliance is to be installed above a built-in electric oven, the electrical connection of the hob and the oven must be carried out separately, both for electrical safety purposes and to make extracting the oven easier. Connecting the supply cable to the mains Install a standardised plug corresponding to the load indicated on the data plate. The appliance must be directly connected to the mains using an omnipolar circuit-breaker with a minimum contact opening of 3 mm installed between the appliance and the mains. The circuit-breaker must be suitable for the charge indicated and must comply with current electrical regulations (the earthing wire must not be interrupted by the circuit-breaker). The supply cable must not come into contact with surfaces with temperatures higher than 50°C. The installer must ensure that the correct electrical connection has been made and that it is compliant with safety regulations. Before connecting to the power supply, make sure that: • the appliance is earthed and the plug is compliant with the law. € the socket can withstand the maximum power of the appliance, which is indicated on the data plate. € the voltage is in the range between the values indicated on the data plate. [. . . ] € There are no draughts near the appliance. Check to make sure that: • The bottom of the cookware is perfectly flat. € The cookware is positioned correctly at the centre of the burner. € The pan support grids have been positioned correctly. [. . . ]