User manual HOTPOINT PH 750 T GH

[. . . ] 12 Operating Instructions HOB Contents IT Italiano, 1 GB GB English, 13 FR Français, 25 Installation, 14-17 ES Español, 39 Positioning Electrical connection Gas connection Data plate Burner and nozzle specifications Description of the appliance, 18 Overall view Start-up and use, 19-21 Practical advice on using the burners Practical advice on using the the Ceramic Glass Module Precautions and tips, 22 PH 760 RF PH 760 RF GH PZ 760 RF PH 760 F PH 750 RT GH PH 750 PH 750 T PH 741 RQO GH PH 730 RT PH 720 RT General safety Disposal Maintenance and care, 23 Switching the appliance off Cleaning the appliance Gas tap maintenance Troubleshooting, 24 Installation GB  Before operating your new appliance please read this instruction booklet carefully. It contains important information for safe use, installation and care of the appliance.  Please keep these operating instructions for future reference. Pass them on to possible new owners of the appliance. [. . . ]  If the appliance is connected to liquid gas, the regulation screw must be fastened as tightly as possible.  Once this procedure is finished, replace the old rating sticker with one indicating the new type of gas used. Stickers are available from any of our Service Centres.  Should the gas pressure used be different (or vary slightly) from the recommended pressure, a suitable pressure regulator must be fitted to the inlet pipe (in order to comply with current national regulations). DATA PLATE Electrical connections • Adjusting the burners’ primary air : Does not require adjusting. Voltage of 220-240V ~ 50/60Hz voltage of 220-230V ~ 50/60Hz maximum power absorbed 2000W (see data plate ) This appliance conforms to the following European Economic Community directives: -73/23/EEC dated 19/02/73 (Low Voltage) and subsequent amendments - 89/336/EEC dated 03/05/89 (Electromagnetic Compatibility) and subsequent amendments - 93/68/EEC dated 22/07/93 and subsequent amendments. 78 MJ/m3 S DC A PH 760 RF PH 760 RF GH PZ 760 RF S SP DC A PH 750 RT GH PH 741 RQO GH S TC DC A DC TC PH 720 RT S DC TC RR UR S S A RR TC S PH 750 T S A RR S PH 760 F S SP A PH 730 RT PH 750  The hob can only be installed above built-in ovens with a cooling ventilation system. 17 Description of the appliance GB Overall view CERAMIC GLASS MODULE* GAS BURNERS Support Grid for COOKWARE INDICATOR LIGHT FOR CERAMIC GLASS MODULE* Control Knobs for GAS BURNERS and ELECTRIC HOTPLATES* SAFETY DEVICES* Ignition for GAS BURNERS* • The INDICATOR LIGHT FOR CERAMIC GLASS MODULE switches on whenever the selector knob is moved from the ‘off’ position. Use the diameter of the cookware to choose the most appropriate burner to cook with. • Control Knobs for GAS BURNERS and ELECTRIC PLATES* adjust the power or the size of the flame. GAS BURNER ignition* enables a specific burner to be lit automatically. • SAFETY DEVICE* stops the gas flow if the flame is accidentally extinguished. 18 Start-up and use The position of the corresponding gas burner or electric hotplate* is shown on every knob. Gas burners Each burner can be adjusted to one of the following settings using the corresponding control knob: • Off Maximum Minimum To light one of the burners, hold a lit match or lighter near the burner and, at the same time, press down and turn the corresponding knob anti-clockwise to the maximum setting. It is possible to turn on only the circular part of the elemement (identified by the letter "A") or the cooking surface can be enlarged by turning on both "A" and "B". To turn only the circular "A" element, simply turn the knob in the clockwise direction to any one of the 12 available settings. To add the "B" section, turn the knob to setting 12 and then click it into the setting. Then proceed by turning the knob in the counter-clockwise direction to one of the 12 settings. The figure shows the heating zones, which become red when the element is turned on. Indicator light to show when the cooking zone is above B 60°C, even after the heating element has been turned off. A GB C When the knob is on any of the settings other than "Off", the Indicator Light for Ceramic Glass Module comes on. Practical advice on using the burners To ensure the burners operate efficiently: • Use appropriate cookware for each burner (see table) so that the flames do not extend beyond the bottom of the cookware. [. . . ] Aluminum foil, plastic Gas tap maintenance Over time, the taps may become jammed or difficult to turn. If this happens, the tap must be replaced.  This procedure must be performed by a qualified technician authorised by the manufacturer. 23 Troubleshooting GB It may happen that the appliance does not function properly or at all. [. . . ]