User manual HOTPOINT PH 760 RF GH U

[. . . ] 12 Operating Instructions HOB Contents PL Polski, 1 GB GB English, 13 Installation, 14-17 Positioning Electrical connection Gas connection Burner and nozzle specifications Data plate Description of the appliance, 18 Overall view Start-up and use, 19-21 Practical advice on using the burners Practical advice on using the the Ceramic Glass Module Precautions and tips, 22 PH 760 RF GH U PZ 760 RF U PH 741 RQO GH U General safety Disposal Maintenance and care, 23 Switching the appliance off Cleaning the appliance Gas tap maintenance Troubleshooting, 24 Installation GB !Before operating your new appliance please read this instruction booklet carefully. It contains important information for safe use, installation and care of the appliance. Please keep these operating instructions for future reference. [. . . ] Remove the knob and adjust the adjustment screw, which is positioned in or next to the tap pin, until the flame is small but steady. Having adjusted the flame to the required low setting, while the burner is alight, quickly change the position of the knob from minimum to maximum and vice versa several times, checking that the flame does not go out. Some appliances have a safety device (thermocouple) fitted. If the device fails to work when the burners are set to the low flame setting, increase this low flame setting using the adjusting screw. Once the adjustment has been made, replace the seals on the by-passes using sealing wax or a similar substance. If the appliance is connected to liquid gas, the regulation screw must be fastened as tightly as possible. Once this procedure is finished, replace the old rating sticker with one indicating the new type of gas used. Stickers are available from any of our Service Centres. Should the gas pressure used be different (or vary slightly) from the recommended pressure, a suitable pressure regulator must be fitted to the inlet pipe (in order to comply with current national regulations). The hob can only be installed above built-in ovens with a cooling ventilation system. Voltage of 220-230V~ o 220240V~ 50/60Hz (see data plate) maximum power absorbed 2000W This appliance conforms to the following European Economic Community directives: -73/23/EEC dated 19/02/73 (Low Voltage) and subsequent amendments - 89/336/EEC dated 03/05/89 (Electromagnetic Compatibility) and subsequent amendments - 93/68/EEC dated 22/07/93 and subsequent amendments. - 90/336/EEC dated 29/06/90 (Gas) and subsequent amendments. - 2002/96/EC 17 Description of the appliance GB Overall view CERAMIC GLASS MODULE* GAS BURNERS Support Grid for COOKWARE INDICATOR LIGHT FOR CERAMIC GLASS MODULE* Control Knobs for GAS BURNERS and ELECTRIC HOTPLATES* SAFETY DEVICES* Ignition for GAS BURNERS* • The INDICATOR LIGHT FOR CERAMIC GLASS MODULE switches on whenever the selector knob is moved from the ‘off’ position. To turn on one of the rings, press the relative knob in all the way and turn it anti-clockwise to the high setting . The burner is fitted with an electronic igniter that automatically starts when the knob is pressed in. Since the burner is equipped with a safety device, after lighting the burner keep the knob pressed in for about 2-3 seconds to allow the device which keeps the flame lit automatically to heat up. The selected burner can be regulated using the corresponding knob, as follows: • Off Maximum Minimum To switch off the burner, turn the knob in a clockwise direction until it stops (when reaches the “•” position). Ceramic Glass Module* This cooktop is fitted with dual-ring radiant heating elements located beneath the glass. It is possible to turn on only the circular part of the elemement (identified by the letter "A") or the cooking surface can be enlarged by turning on both "A" and "B". To turn only the circular "A" element, simply turn the knob in the clockwise direction to any one of the 12 available settings. To add the "B" section, turn the knob to setting 12 and then click it into the setting. Then proceed by turning the knob in the counter-clockwise direction to one of the 12 settings. [. . . ] This procedure must be performed by a qualified technician authorised by the manufacturer. 23 Troubleshooting 03/2005 - 195042707. 01 XEROX BUSINESS SERVICES GB It may happen that the appliance does not function properly or at all. Before calling the service centre for assistance, check if anything can be done. [. . . ]