User manual HOTPOINT PH 941MSTV GH/HA EE

[. . . ] PH 941MSTV GH/HA EE Magyar Használati útmutató Főzőlap Tartalomjegyzék Használati útmutató, 1 Figyelmeztetések, 3 Szerviz, 4 A készülék leírása, 6 Beszerelés, 21 Bekapcsolás és használat, 25 Óvintézkedések és tanácsok, 26 Karbantartás és ápolás, 26 Hibaelhárítás, 27 English Operating Instructions HOB Contents Operating Instructions, 1 Warnings, 2 Assistance, 4 Description of the appliance, 5 Installation, 7 Start-up and use, 11 Precautions and tips, 12 Maintenance and care, 12 Troubleshooting, 13 Polski Instrukcja obsługi PŁYTA Spis treści Instrukcja obsługi, 1 Ostrzezenia, 2 Serwis Techniczny, 4 Opis urządzenia, 5 Instalacja, 14 Uruchomienie i użytkowanie, 18 Zalecenia i środki ostrożności, 19 Konserwacja i utrzymanie, 19 Anomalie i środki zaradcze, 20 CAUTION: the use of inappropriate hob guards can cause accidents. Warnings WARNING: The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements. Children less than 8 years of age shall be kept away unless continuously supervised. [. . . ] When the installation process is complete, check the pipe fittings for leaks using a soapy solution. Adapting to different types of gas To adapt the hob to a different type of gas other than default type (indicated on the rating plate at the base of the hob or on the packaging), the burner nozzles should be replaced as follows: 1. Remove the hob grids and slide the burners off their seats. Unscrew the nozzles using a 7 mm socket spanner, and replace them with nozzles for the new type of gas (see table 1 “Burner and nozzle characteristics”). Reassemble the parts following the above procedure in the reverse order. Once this procedure is finished, replace the old rating sticker with one indicating the new type of gas used. Sticker are available from any of our Service Centres. replacing the Triple ring burner nozzles 1. Remove the pan supports and lift the burners out of their housing. The burner consists of two separate parts (see pictures). Unscrew the nozzles using a 7 mm socket spanner. Replace the nozzles with models that are configured for use with the new type of gas (see Table 1). The two nozzles have the same hole diameter. Replace all the components by completing the above operations in reverse order. • Setting the burners to minimum 1. Turn the tap to the low flame position; 2. Emove the knob and adjust R the adjustment screw, which is positioned in or next to the tap pin, until the flame is small but steady. Having adjusted the flame to the required low setting, while the burner is alight, quickly change the position of the knob from minimum to maximum and vice versa several times, checking that the flame does not go out. Some appliances have a safety device (thermocouple) fitted. If the device fails to work when the burners are set to the low flame setting, increase this low flame setting using the adjusting screw. Once the adjustment has been made, replace the seals on the by-passes using sealing wax or a similar substance. If the appliance is connected to liquid gas, the regulation screw must be fastened as tightly as possible. [. . . ] This holds true for chemically aggressive cleaners, like oven sprays and stain removers. € Stainless steel can be marked by hard water that has been left on the surface for a long time, or by aggressive detergents containing phosphorus. After cleaning, rinse and dry any remaining drops of water. The burner does not light or the flame is not even around the burner. [. . . ]