User manual HOTPOINT PHN 962 TS/IX/A

[. . . ] PHN 932 T2/IX/A PHN 961 TS/IX/A PHN 962 TS/IX/A Español Manual de instrucciones ENCIMERA Sumario Manual de instrucciones, 1 Advertencias, 4 Asistencia, 6 Descripción del aparato, 7 Instalación, 22 Puesta en funcionamiento y uso, 26 Precauciones y consejos, 26 Mantenimiento y cuidados, 27 Anomalías y soluciones, 27 English Portuges Operating Instructions HOB Contents Operating Instructions, 1 Warnings, 3 Assistance, 6 Description of the appliance, 7 Installation, 9 Start-up and use, 13 Precautions and tips, 13 Maintenance and care, 14 Troubleshooting, 14 Instruções para a utilização PLANO Índice Instruções para a utilização, 1 Advertências, 4 Assistência, 6 Descrição do aparelho, 7 Instalação, 29 Início e utilização, 33 Precauções e conselhos, 33 Manutenção e cuidados, 34 Anomalias e soluções, 34 Français 中文 Mode d’emploi TABLE DE CUISSON Sommaire Mode d’emploi, 1 Avertissements, 3 Assistance, 6 Description de l’appareil, 7 Installation, 15 Mise en marche et utilisation, 19 Précautions et conseils, 19 Nettoyage et entretien, 20 Anomalies et remèdes, 20 操作说明 炉盘 目录 操作说明, 1 警告, 5 帮助, 6 器具 说明 , 8 安装 , 36 启动和使用 , 40 注意事项和技 , 40 维护与保养, 41 故障排除, 41 ‫عربی‬ ‫تعليمات التشغيل‬ ‫محتويات‬ ‫رف تسخين‬ ‫تعليمات التشغيل،2‬ ‫تحذيرات،5‬ ‫المساعدة،6‬ ‫وصف الجهاز،8‬ ‫التركيب،34‬ ‫التشغيل واالستخدام،74‬ ‫وسائل تحذير ونصائح،74‬ ‫الصيانة والعناية،64‬ ‫استكشاف المشاكل وحلها،64‬ Warnings WARNING: The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements. Children less than 8 years of age shall be kept away unless continuously supervised. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. [. . . ] When the installation process is complete, check the pipe fittings for leaks using a soapy solution. Adapting to different types of gas To adapt the hob to a different type of gas other than default type (indicated on the rating plate at the base of the hob or on the packaging), the burner nozzles should be replaced as follows: 1. Remove the hob grids and slide the burners off their seats. Unscrew the nozzles using a 7 mm socket spanner, and replace them with nozzles for the new type of gas (see table 1 “Burner and nozzle characteristics”). Reassemble the parts following the above procedure in the reverse order. Once this procedure is finished, replace the old rating sticker with one indicating the new type of gas used. Sticker are available from any of our Service Centres. € Adjusting the burners’ primary air Does not require adjusting. Electrical connection Hobs equipped with a three-pole power supply cable are designed to operate with alternating current at the voltage and frequency indicated on the data plate (this is located on the lower part of the appliance). The earth wire in the cable has a green and yellow cover. If the appliance is to be installed above a built-in electric oven, the electrical connection of the hob and the oven must be carried out separately, both for electrical safety purposes and to make extracting the oven easier. Connecting the supply cable to the mains Install a standardised plug corresponding to the load indicated on the data plate. The appliance must be directly connected to the mains using an omnipolar circuit-breaker with a minimum contact opening of 3 mm installed between the appliance and the mains. The circuit-breaker must be suitable for the charge indicated and must comply with current electrical regulations (the earthing wire must not be interrupted by the circuit-breaker). The supply cable must not come into contact with surfaces with temperatures higher than 50°C. The installer must ensure that the correct electrical connection has been made and that it is compliant with safety regulations. Before connecting to the power supply, make sure that: • the appliance is earthed and the plug is compliant with the law. € the socket can withstand the maximum power of the appliance, which is indicated on the data plate. € the voltage is in the range between the values indicated on the data plate. Since the burner is fitted with a safety device, the knob should be pressed for approximately 2-3 seconds to allow the automatic device keeping the flame alight to heat up. When using models with an ignition button, light the desired burner pressing down the corresponding knob as far as possible and turning it anticlockwise towards the maximum setting. If a flame is accidentally extinguished, turn off the control knob and wait for at least 1 minute before trying to relight it. [. . . ] € All the movable parts that make up the burner are mounted correctly. € There are draughts near the appliance. The flame dies in models with a safety device. Check to make sure that: • You pressed the knob all the way in. [. . . ]