User manual HOTPOINT PK 640 GH /HA

[. . . ] 15 Operating Instructions HOB Contents Installation, 17-22 IT Italiano, 1 GB GB English, 16 FR Français, 30 ES Español, 47 Positioning Electrical connection Gas connection Data plate Burner and nozzle specifications Description of the appliance, 23 Overall view Start-up and use, 24-26 Practical advice on using the burners Practical advice on using the the Ceramic Glass Module Precautions and tips, 27 PK 741 RQO GH /HA PK 750 X /HA PK 750 AX /HA PK 750 GH /HA PK 750 R GH /HA PK 750 RT X /HA PK 750 RT AX /HA PK 750 RT GH /HA PK 750 T X /HA PK 750 T GH /HA PK 760 RF X /HA PK 760 RF GH /HA PK 750 RL GH /HA PK 750 RTL GH /HA PK 750 TL GH /HA PK 630 RT GH/HA PK 630 RTL GH/HA PK 640 GH/HA PK 640 X/HA PK 640 RL GH/HA PK 640 RGH/HA PK 640. 1 RGH/HA PK 640 RAX /HA General safety Disposal Maintenance and care, 28 Switching the appliance off Cleaning the appliance Gas tap maintenance Troubleshooting, 29 16 Installation !Before operating your new appliance please read this instruction booklet carefully. It contains important information for safe use, installation and care of the appliance. [. . . ] Since the burner is fitted with a safety device, the knob should be pressed for approximately 2-3 seconds to allow the automatic device keeping the flame alight to heat up. When using models with an ignition button, light the desired burner pressing down the corresponding knob as far as possible and turning it anticlockwise towards the maximum setting. If a flame is accidentally extinguished, turn off the control knob and wait for at least 1 minute before trying to relight it. To switch off the burner, turn the knob in a clockwise direction until it stops (when reaches the “•” position). Discrete flame adjustment The selected burner can be adjusted - by means of the knob - to 5 different power levels. To shift between levels, simply turn the knob towards the desired power level. A click signals the passage from one power level to the other. The selected power level is indicated by the corresponding symbol ) and, on (symbols hobs equipped with a display, by the LEDs that turn on (5 = max. The system guarantees accurate flame adjustment and uniform cooking results by facilitating selection of the desired power level. The "double-flame" burner This gas burner consists of two concentric flame rings that can operate jointly or independently (in case of dual-control only). As the burner is fitted with a safety device, the knob should be pressed down for approximately 2-3 seconds until the device keeping the flame automatically alight heats up. Dual control: Each ring comprising the burner has its own control knob: controls the The knob marked with the symbol outer ring. Controls the The knob marked with the symbol inner ring. To activate any one of the two rings, press the corresponding knob and turn it anti-clockwise to the . Maximum power setting In order to use the double-flame burner to its full potential, avoid simultaneously setting the inner ring to minimum power and the outer ring to maximum power. Single control: The rings comprising the burner are activated through a single control knob. To simultaneously turn on both rings, position the (max. ) then press knob on the symbol and turn the knob anti-clockwise. To turn on the inner ring only, position the knob on (max. ) then press and turn the symbol the knob clockwise. (to switch modes, it is necessary to switch off the burner). To switch off the burner, press and turn the knob clockwise until it stops (when it reaches the "•" position). [. . . ] Clean the cooking surface when it is still warm with a suitable cleaning product (such as the one in the Solutions product line available from any AfterSales Service Centre) and paper towels. Aluminum foil, plastic Gas tap maintenance Over time, the taps may become jammed or difficult to turn. If this happens, the tap must be replaced. This procedure must be performed by a qualified technician authorised by the manufacturer. [. . . ]