User manual HOTPOINT PZ 750 R GH NG

[. . . ] For any service, contact the place of purchase or the nominated service agent. The appliance was designed for domestic use inside the home and is not intended for commercial or industrial use. The appliance must not be installed outdoors, even in covered areas. It is extremely dangerous to leave the appliance exposed to weather. [. . . ] This unit must only be installed by an authorised person. This appliance must not be installed in marine craft or recreational vehicles. Fitting the cooktop into cabinetry The following minimum clearances to combustible materials must be observed: Minimum clearance from edge of burner to side wall must be 200 mm. Minimum clearance from edge of burner to rear wall must be 200 mm. Minimum clearance from top of highest burner to cupboard above hob burners must be 600 mm. Compliance with standards This cooktop must be installed in accordance with the requirements of local gas and electrical authorities, as well as the latest published versions of the following standards: AS/NZS 5601 Gas Installation code SAA Wiring Rules Dimensions of cutout The following diagram indicates the dimensions of the required cutout. In placing the cooktop, suitable insulation between the cooktop undersurface and the top of the bench should be used. Wherever possible, the cooktop should be secured to the benchtop using clamps. 555 mm 475 mm 55 m m Fixing to the housing unit Proceed with fixing to the housing unit as follows (see figure above). Mount the hooks, partly tightening the screws into the holes. Position the sealing gasket approximately 5-6 mm from the edge of the installation hole, matching up the two ends of the seal without overlapping. Insert the hob into the cutout, making sure it is positioned centrally and that the edge adheres to the sealant Position the hooks correctly, as shown in the figure, and then tighten the screws to hold them in place. INSTALLER: Please also ensure that the duplicate data label supplied, be affixed in a suitable easily accessible location such as an adjacent cupboard or drawer, for future reference. Dimensions (mm) length (side to side) width (front to back) depth PZ640 600 510 44 PZ750 750 510 44 Range hoods Range hoods and overhead exhaust fans must be installed according to manufacturers’ instructions but in no case shall clearance from hob burners be less than 600 mm for range hoods and 750 mm for overhead exhaust fans. Adjacent cabinetry It is recommended that the adjacent kitchen surfaces should be capable of withstanding temperatures of 100°C. 4 Installation Fitting the cooktop above an oven When installing the cooktop above an oven, both the electricity supply cable and the gas pipe or flexible hose must not touch hot parts of the oven housing. When installing above a built-under oven without forced cooling ventilation, suitable air vents should be provided for as shown in the figure (inlet at least 200 cm² from the bottom, outlet at least 120 cm² from the top part) to allow adequate ventilation inside the housing unit. Also a wooden panel “A” should be installed beneath the hob as insulation, positioning it at a minimum distance of 15 mm from the hob housing Electrical connection The electrical supply for the cooktop must be a 240 Volt 50 Hz. The fuse and electrical wiring of the home/premises must support the load of the appliance. A 3 pin flexible power cord is supplied with the appliance to allow the cooktop to be connected to a properly earthed and rated power socket. The flexible cord of the appliance must not be subject to direct heat and must be positioned after installation of the appliance so that its temperature does not exceed 75°C. IMPORTANT If a power socket needs to be installed or relocated, the work must be done by a licensed electrician. Gas type conversion If the hob is to be converted for use with a type of gas other than that for which it was set in the factory (indicated on the cooktop data plate), the burner injectors must be replaced as follows: Remove the pan supports and the burners. Unscrew the injectors (“A” in fiugure below) using a 7 mm socket wrench, and replace them with injectors of suitable orifice diameter, as indicated on the appliance data plate. Reassemble the parts. 200 cm² Gas connection This appliance is suitable for use with either a flexible connection or rigid copper connection. If installing the appliance with a flexible connection, the flexible connection must be approved to class B or D of AS/NZS1869 as a minimum. Fit regulator supplied for Natural Gas (if applicable) at rear of appliance, and as close as practicable to the appliance. It is recommended that an isolating valve and union be fitted, to enable simple disconnection for servicing. These are to be in an accessible location. Flexible hose If a flexible hose is used, it should be as short as possible with a maximum length of 1. 5 metres; it should not be bent or kinked; it should not be in contact with the rear wall of the appliance or in any case with parts which may reach a temperature of 50°C; it should not come into contact with pointed parts or sharp corners; it should be easy to inspect along its entire length in order to be able to check its condition. [. . . ] Care should be taken when cleaning around graphics. Never use steam cleaners or pressure cleaners on the appliance. Burners Wait for the cooktop to cool completely. Remove the burner cap and check the gas outlet holes for blockages. Clean with a soft bristle brush and warm soapy water. [. . . ]