User manual HOTPOINT TCD G51

[. . . ] Instruction booklet TUMBLE DRYER GB English, 1 F Français, 18 P Português, 35 Contents Important information, 2-3 Installation, 4 Where to put your dryer Ventilation Door reversal instructions Water drain Electrical connection Before you start using your dryer GB GR EÏÏËÓÈο, 52 Dryer description, 5 To open the door The features Control panel The Display, 6-8 Start and programmes, 8-11 TCD G51 First time you turn on your dryer you must select your preferred language see page 6 Choosing a programme Special programmes Programme option modifiers Table of programmes The controls Laundry, 12-13 Sorting your laundry Wash care labels Special clothing items Drying times Warnings and Suggestions, 14 General safety Disposal Saving energy and respecting the environment Maintenance and Care, 15 Switching off the electricity Cleaning the filter after each cycle Empty the water container after each cycle Check the drum after each cycle Cleaning the condenser unit Cleaning the dryer Troubleshooting, 16 Service, 17 Spare parts !Keep this instruction booklet on hand in order to refer to it when necessary. Take it with you when you move, and should you sell this appliance or pass it on to another party, make sure that this booklet is supplied along with the dryer so that the new owner may be informed about warnings and suggestions on how the appliance works. Read these instructions carefully; the following pages contain important information on installation and suggestions on how the appliance works. [. . . ] A programme must have been selected, by pressing a programme selection button, before an option can be selected. Not all options are available for all programmes (see Programmes Table). If an option is not available and you press the button, the buzzer will beep 3 times. If the option is available the indicator, on the display unit next to the bottom buttons, lights to show that the option has been selected. Time Delay The start of some programmes (see The Display and Start and Programmes) can be delayed for up to 24 hours. Ensure the water container is emptied before setting a delayed start. pre Care This option is only available if a delayed start has been selected. It tumbles the clothes occasionally during the delayed period to help prevent creases developing. Alarm Available on all programmes and allows the buzzer to give a signal at the end of the drying cycle, to remind you that the clothes are ready to be removed. Post Care When available and selected, the clothes are occasionally tumbled after the end of the drying and cool tumble cycles, to help prevent creases developing should you not be available to remove the load immediately the programme is complete. TIME DISPLAY 88:88 The display shows either the amount of time delay remaining or an indication of the amount of time left for a drying programme (see The Display). The delay or time to end is displayed in hours and minutes and counts down each minute. When timed programmes are selected the time displayed throughout the cycle is the actual time remaining. When an Automatic programme is selected, the time displayed is an estimate of the time remaining. When the programme is selected the display shows the time required to dry a full load, after around 10 minutes the controller calculates a better estimate of the cycle time. The colons between the hours and minutes in the display flash to show that the time is counting down. The display also shows if there is a problem with your dryer, if this occurs the display will show F followed by a fault code number (see Troubleshooting). Q Empty Water Container (If you have plumbed your dryer to a drain this icon can be ignored, as there is no need to empty the water container). Messages are displayed to reminds you to empty the water container. If the water container fills during a programme, the heater turns off and the dryer does a period of Cool Tumble. After this it stops and a message tells you to EMPTY THE WATER CONTAINER . You must empty the water container and restart the dryer or the clothes will not dry. [. . . ] If an automatic programme has not sensed the required final moisture in this time the dryer will complete the programme and stop. Check the above points and run the programme again, if the results are still damp, contact the Service Centre (see Service). Q The display shows a fault code F followed by one or two numbers. Q If the display shows F10 or F15: - Turn off and remove the plug. [. . . ]