User manual HOTPOINT THC 642 W/IX/HA EE

[. . . ] THC 642 W/IX/HA EE Polski Instrukcja obsługi PŁYTA Spis treści Instrukcja obsługi, 1 Ostrzezenia, 4 Serwis Techniczny, 7 Opis urządzenia, 8 Instalacja, 21 Uruchomienie i użytkowanie, 25 Zalecenia i środki ostrożności, 25 Konserwacja i utrzymanie, 26 Anomalie i środki zaradcze, 26 English Eesti keeles Operating Instructions HOB Contents Operating Instructions, 1 Warnings, 3 Assistance, 7 Description of the appliance, 8 Installation, 10 Start-up and use, 13 Precautions and tips, 13 Maintenance and care, 14 Troubleshooting, 14 Kasutusjuhend KEEDUPLAAT Sisukord Kasutusjuhend, 1 Hoiatused, 4 Klienditugi, 7 Seadme kirjeldus, 8 Paigaldamine, 27 Käitamine ja kasutamine, 31 Ettevaatusabinõud ja soovitused, 31 Hooldus, 32 Veaotsing, 32 Română Lietuvių k. мұны Пайдалану нұсқаулығы, 2 Ескертулер, 6 Көмек, 7 Құрылғы сипаттамасы, 9 Орнату, 52 Қосу және пайдалану, 56 Сақтандырулар мен кеңестер, 56 Жөндеу және күтім, 57 Ақаулықтарды жою, 57 Warnings WARNING: The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements. Children less than 8 years of age shall be kept away unless continuously supervised. [. . . ] € the socket is compatible with the plug of the appliance. If the socket is incompatible with the plug, ask an authorised technician to replace it. Once the appliance has been installed, the power supply cable and the electrical socket must be easily accessible. connection with a rigid pipe (copper or steel) !Connection to the gas system must be carried out in such a way as not to place any strain of any kind on the appliance. There is an adjustable L-shaped pipe fitting on the appliance supply ramp and this is fitted with a seal in order to prevent leaks. The seal must always be replaced after rotating the pipe fitting (seal provided with appliance). These pipes must be installed so that they are never longer than 2000 mm when fully extended. Once connection has been carried out, make sure that the flexible metal pipe does not touch any moving parts and is not compressed. Only use pipes and seals that comply with current national regulations. Checking the tightness of the connection !When the installation process is complete, check the pipe fittings for leaks using a soapy solution. Adapting to different types of gas To adapt the hob to a different type of gas other than default type (indicated on the rating plate at the base of the hob or on the packaging), the burner nozzles should be replaced as follows: 1. Remove the hob grids and slide the burners off their seats. Unscrew the nozzles using a socket spanner of the appropriate size, and replace them with nozzles for the new type of gas (see table 1 “Burner and nozzle characteristics”). Reassemble the parts following the above procedure in the reverse order. Once this procedure is finished, replace the old rating sticker with one indicating the new type of gas used. Sticker are available from any of our Service Centres. 11 GB • Adjusting the burners’ primary air Does not require adjusting. • Setting the burners to minimum 1. Turn the tap to the low flame position; 2. Remove the knob and adjust the adjustment screw, which is positioned in or next to the tap pin, until the flame is small but steady. [. . . ] € If you are cooking something that takes a long time, it’s worth using a pressure cooker, which is twice as fast and saves a third of the energy. Maintenance and care Switching the appliance off Cleaning the hob surface Disconnect your appliance from the electricity supply before carrying out any work on it. € All the enamelled and glass parts should be cleaned with warm water and neutral solution. € Stainless steel surfaces may be stained by calcareous water or aggressive detergents if left in contact for too long. [. . . ]