User manual HOTPOINT TQG 751 W/A

[. . . ] TQG 752 W/A(ICE) ‫تعليمات التشغيل‬ ‫المحتويات‬ ‫رف تسخين‬ 1،‫تعليمات التشغيل‬ 3،‫تحذيرات‬ 4،‫المساعدة‬ 5،‫وصف الجهاز‬ 19 ،‫التركيب‬ 23،‫بدء التشغيل واالستخدام‬ 23 ،‫وسائل الحذر والنصائح‬ 22 ،‫استكشاف المشاكل وحلها‬ 22 ،‫الصيانة والعناية‬ English Operating Instructions HOB Contents Operating Instructions, 1 Warnings, 2 Assistance, 4 Description of the appliance, 5 Installation, 6 Start-up and use, 10 Precautions and tips, 10 Maintenance and care, 11 Troubleshooting, 11 Français Mode d’emploi TABLE DE CUISSON Sommaire Mode d’emploi, 1 Avertissements, 2 Assistance, 4 Description de l’appareil, 5 Installation, 12 Mise en marche et utilisation, 16 Précautions et conseils, 16 Nettoyage et entretien, 17 Anomalies et remèdes, 17 Warnings WARNING: The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements. Children less than 8 years of age shall be kept away unless continuously supervised. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. [. . . ] The hob can only be installed above built-in ovens with a cooling ventilation system. Electrical connection Hobs equipped with a three-pole power supply cable are designed to operate with alternating current at the voltage and frequency indicated on the data plate (this is located on the lower part of the appliance). The earth wire in the cable has a green and yellow cover. If the appliance is to be installed above a built-in electric oven, the electrical connection of the hob and the oven must be carried out separately, both for electrical safety purposes and to make extracting the oven easier. Connecting the supply cable to the mains Install a standardised plug corresponding to the load indicated on the data plate. The appliance must be directly connected to the mains using an omnipolar circuit-breaker with a minimum contact opening of 3 mm installed between the appliance and the mains. The circuit-breaker must be suitable for the charge indicated and must comply with current electrical regulations (the earthing wire must not be interrupted by the circuit-breaker). The supply cable must not come into contact with surfaces with temperatures higher than 50°C. The installer must ensure that the correct electrical connection has been made and that it is compliant with safety regulations. Before connecting to the power supply, make sure that: • the appliance is earthed and the plug is compliant with the law. € the socket can withstand the maximum power of the appliance, which is indicated on the data plate. € the voltage is in the range between the values indicated on the data plate. € the socket is compatible with the plug of the appliance. If the socket is incompatible with the plug, ask an authorised technician to replace it. Once the appliance has been installed, the power supply cable and the electrical socket must be easily accessible. The cable must not be bent or compressed. The cable must be checked regularly and replaced by authorised technicians only (see Assistance). Reassemble the parts following the above procedure in the reverse order. Once this procedure is finished, replace the old rating sticker with one indicating the new type of gas used. Sticker are available from any of our Service Centres. € Adjusting the burners’ primary air Does not require adjusting. 7 GB • Setting the burners to minimum 1. [. . . ] First, check to see that there are no interruptions in the gas and electrical supplies, and, in particular, that the gas valves for the mains are open. The burner does not light or the flame is not even around the burner. Check whether: • The gas holes on the burner are clogged. € All the movable parts that make up the burner are mounted correctly. [. . . ]