User manual HP 9000 MODEL 735/125 WORKSTATION

[. . . ] HEWLETT­PACKARD MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance or use of this material. Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished by Hewlett-Packard. This document contains proprietary information which is protected by copyright. [. . . ] If you use these preconfigured device files and drivers, you won't need to configure your CD-ROM drive with the operating system. SCSI ID and Device File Information for HP-UX 9. 05 The default device files for the CD-ROM drive are in the /dev/dsk or /dev/rdsk directories. The underlined number located in the sixth position in the device file name indicates the SCSI address used in the file. For example, the device file c201d2s0 located in /dev/dsk was created for SCSI address 2. SCSI ID and Device File Information for HP-UX 10. 0 The default device file names for the CD-ROM is /dev/[r]dsk/c#t#d# where: c# identifies the bus address of the SCSI interface card t# identifies the target address of the SCSI disk d# identifies the SCSI lun address (0, except for disk arrays) Device file names for CD-ROM drives at HP-UX 10. 0 depend on the naming conventions of the system on which you are installing. To create your own device files, you must reconfigure your drive with the operating system. You can use either the System Administration Manager (SAM) or HP-UX commands to set up the kernel and device files. With each, you must perform the following steps: 1. Check the kernel for a device driver. If the device driver is not there, you must create one and then reconfigure the kernel. Create the appropriate device files. 2. 3. Add a CD-ROM file system (cdfs). 2­2 Using Your CD-ROM Drive Controls and Features of the CD-ROM Drive Figure 2­1 shows the operating controls and features of the CD-ROM drive. Table 2­1 describes each of these controls and features. CD-ROM Disc Loading Tray Headphone Jack Emergency Eject Volume Control Busy Indicator Load/Eject Button Figure 2­1. CD-ROM Drive Controls and Features 2­3 Using Your CD-ROM Drive Table 2­1. The emergency eject feature allows you to eject the disc tray if the normal procedure fails. See Table 2­1 earlier in this chapter. You must unmount the disc before ejecting it from the drive. Refer to "Unmounting a CD-ROM Disc, later in this chapter. " NOTICE: 2. Wait until the drive has fully ejected the disc tray, then remove the disc from the tray as shown in Figure 2­4. Be careful to touch only the edges of the disc. Figure 2­4. Removing the CD-ROM Disc From the Disc Tray (Horizontal Mount) 3. To close the disc tray, push the front of the disc tray gently towards the drive until it closes by itself. 2­8 Using Your CD-ROM Drive Loading a CD-ROM Disc in a Vertically Mounted Drive NOTICE: This procedure is the same for a CD-ROM drive mounted with the EJECT button positioned up or down. 1. Hold the disc with the label side to the left and place the edge of the disc onto disc holders A and B, as shown in Figure 2­5. Press down gently against the spring tension of disc holders A and B and swing the top of the disc in until it is held by disc holder C (and disk holder D on some models). To close the disc tray, push the front of the disc tray gently towards the drive until it closes by itself. Disc Holder D ­ hidden (not on all models) 2. 3. Disc Holder C Disc Holder A Disc Holder B Figure 2­5. Inserting a CD-ROM Disc (Vertical Mount) 2­9 Using Your CD-ROM Drive Unloading a CD-ROM Disc in a Vertically Mounted Drive 1. Press the eject button to eject the disc tray from the drive. If the drive is in use, you must you must unmount the disc to eject the disc tray. The emergency eject feature allows you to eject the disc tray if the normal procedure fails. [. . . ] 3. Please refer to the system Owner's Guide for the procedures to power off the system. Unplug the system unit power cord and the power cords of any peripheral devices from the power source. Unplug the system unit power cord from the back of the system unit. WARNING: Failure to properly shut down and remove power from the system may create a personal hazard, or may result in hardware damage or data corruption. Removing and Replacing the CD-ROM Drive To open your system and remove and reinstall the CD-ROM drive, refer to the system Owner's Guide. Pre-installation information appears in Chapter 1 of this document. 3­12 Appendix A Safety and Regulatory Statements This appendix contains the following safety and regulatory statements: · · · · · · Emissions regulations Emissions regulations compliance Acoustics Electrostatic discharge precautions Laser safety statement Warnings and cautions A­1 Safety and Regulatory Statements Emissions Regulations Federal Communications Commission (FCC) The Federal Communications Commission of the U. S. [. . . ]