User manual HP ARMADA 1100

[. . . ] Notice The information in this guide is subject to change without notice. Compaq Computer Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material. This guide contains information protected by copyright. No part of this guide may be photocopied or reproduced in any form without prior written consent from Compaq Computer Corporation. [. . . ] Disconnect the AC Adapter from the electrical outlet (Figure 5-2). 5. Disconnect the AC Adapter power cord from the computer (Figure 5-3). Open the battery compartment by lifting up the front of the computer [1] and sliding the battery compartment release button to the right [2]. Lower the compartment [3] (Figure 5-4). 8. Remove the battery pack (Figure 5-5). >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<< Metal objects can damage the battery pack and the connectors inside the compartment. To prevent damage, do not let metal objects touch any of the connectors. Do not place any objects other than the battery pack in the battery compartment. >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<< 9. >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<< When installing a battery pack, do not drop it into the compartment. There are pressure sensitive contacts at the bottom of the compartment that can be damaged or crushed, resulting in intermittent charging, power, or loss of functionality. To install a battery pack, open the battery compartment, hold the unit at a 45- degree angle, and gently slide the battery pack into the compartment. >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<< 10. Remove any installed PC Cards by pulling the top or bottom PC Card release lever to the left to release the card. (PC Card release levers are located on the front of the computer on the left side. ) Gently grasp the card and pull it out (Figure 5-6). Handle Bracket This procedure is necessary if replacing the handle bracket or if separating the display assembly from the system unit module. Removing the Handle Bracket To remove the handle bracket, follow these steps: 1. Turn the computer off and remove all external devices, including the battery pack and the AC Adapter. Remove the diskette and PC Card, if installed (Section 5. 3). Close the computer and turn it topside down. Move the tilt foot toward the front of the computer, exposing the handle bracket screw on either side of the computer (Figure 5-7). 4. Remove the screw and washer from each handle bracket. These screws are not reusable and must be discarded. Remove the handle bracket (Figure 5-8). 6. [. . . ] Automobile Adapter =========================================================================== Auto Adapter Power Supply Ratings Power Supply (Input) Nominal Voltage 13. 8 VDC Operating Voltage 10. 5 - 14. 8 VDC Maximum Voltage 16. 0 VDC Input Fuse Protection 8. 0 A Power Supply (Output) Nominal Voltage 120 VAC Load Regulated Voltage 108 - 125 VAC Line Regulated Voltage 105 to 125 VAC Output Frequency 60 Hz +/- 3 Hz Output Overload Protection 150W @ 2 sec. =========================================================================== System Interrupts Table 7-9 =========================================================================== Hardware IRQ System Function =========================================================================== IRQ0 Timer interrupt IRQ1 IRQ2 IRQ3 IRQ4 IRQ5 IRQ6 IRQ7 Keyboard Interrupt controller cascade COM 2 - used by MSIO or PCMCIA controller COM 1 - used by MSIO or PCMCIA controller Available for use Diskette Drive controller Available for use IRQ8 IRQ9 IRQ10 IRQ11 IRQ12 IRQ13 IRQ14 IRQ15 Real-Time Clock (MSIO) Available for use Available for use Available for use Mouse Floating point error input Hard Drive IRQA EPP parallel port =========================================================================== System DMA Table 7-10 =========================================================================== Hardware DMA System Function =========================================================================== DMA 0/A (mappable) Not assigned DMA 1/B DMA 2 DMA 3 DMA 4 DMA 5 DMA 6 PCMCIA controller Diskette drive controller EPP parallel port Not assigned Not assigned Not assigned DMA 7 Not assigned --------------------------------------------------------------------------NOTE: PC Card controller can use DMA 1, 2, or 5. =========================================================================== System I/O Address Table 7-11 =========================================================================== I/O Address (Hex) System Function (Shipping Configuration) =========================================================================== 000 - 00F Master DMA Controller # 1 010 - 011 012 - 01F 020 - 021 022 - 024 025 - 03F Unused Unused Peripheral Interrupt Controller # 1 Opti Chipset Configuration Registers Unused 040 - 043 044 - 05F 060 061 062 - 063 064 065 - 06F 070 071 072 - 073 074 075 076 077 - 077F 080 - 08F 084 - 085 090 - 091 092 093 - 09F Counter/Timer Registers Unused Keyboard Data Port B Unused Keyboard Command/Status Unused CMOS Index Address CMOS Data Unused Reserved Unused Reserved Unused DMA Page Registers POST Code Output Port Unused Fast Reset Register Unused --------------------------------------------------------------------------I/O Address (Hex) System Function (Shipping Configuration) --------------------------------------------------------------------------0A0 - 0A1 0A2 - 0BF 0C0 - 0DF 0E0 - 0E1 0E2 - 0E3 0E4 - 0EF 0F0 - 0F1 0F9 0FA 0FB Interrupt Controller # 2 Unused DMA Controller # 2 Unused MSIO Configuration Registers Unused NCP Numerics Register Unused Unused Unused 0FC - 0FF 100 - 101 103 - 16F 170 - 177 178 - 1EF 1F0 - 1F7 1F8 - 1FF 200 - 21F 220 - 22F 230 - 23F 240 - 24F 250 - 25F 260 - 277 278 - 27A 27B - 27F Unused Unused Unused Hard Drive Secondary Registers Unused Hard Drive Primary Registers Unused Unused Unused Unused Unused Unused Unused LPT2 and High Speed Parallel Port Registers LPT2 High Speed Printer Port Registers --------------------------------------------------------------------------I/O Address (Hex) System Function (Shipping Configuration) --------------------------------------------------------------------------280 - 2F7 2F8 - 2FF 300 - 36F 370 - 371 372 373 374 375 376 377 378 - 37A 37B - 37F 380 - 387 388 - 38B 38C - 3AF Unused Serial Control Register COM2 Unused Reserved Diskette Digital Output Register Unused Reserved Diskette Main Status/Data Registers Reserved Diskette Input/Control Registers LPT1 and High Speed Parallel Port Registers Unused Unused Unused Unused 3B0 - 3BB 3BC - 3BE 3BF 3C0 - 3CD 3D0 - 3DF 3F0 - 3F7 3F8 - 3FF 400 - 4CF 480 - 48F 4D0 - CF6 CF7 CF8 - CFB CFC - CFF Cirrus Logic Video Controller LPT3 and High Speed Parallel Port Registers LPT1 High Speed Parallel Port Registers Cirrus Logic Video Controller Cirrus Logic Video Controller Diskette Drive Controller Primary Registers COM1 Serial Controller Registers Unused Extended DMS Registers Unused Configuration/NVM Data Register PCI Configuration Index Register PCI Configuration Data Register D00 - FFF Unused =========================================================================== System Memory Map Table 7-12 =========================================================================== Size Memory Address System Function =========================================================================== 640 K 00000000 - 0009FFFF Base Memory 128 K 48 K 160 K 64 K 15 M 58 M 58 M 2M 4G 000A0000 - 000BFFFF 000C0000 - 000CBFFF 000C8000 - 000E7FFF 000E8000 - 000FFFFF 00100000 - 00FFFFFF 01000000 - 047FFFFF 04800000 - 07FFFFFF 08000000 - 080FFFFF 08200000 - FFFEFFFF Video Memory Video BIOS Unused System BIOS Extended Memory Super Extended Memory Unused Video Memory (Direct Access) Unused 64 K FFFF0000 - FFFFFFFF System BIOS ("SHADOW") =========================================================================== Appendix A - Connector Pin Assignments This appendix contains the pin assignments for all external connectors. Table A-1. Parallel Connector =========================================================================== Pin Signal =========================================================================== 1 Strobe * 2 3 4 5 6 7 8 9 Data Bit 0 Data Bit 1 Data Bit 2 Data Bit 3 Data Bit 4 Data Bit 5 Data Bit 6 Data Bit 7 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Acknowledge * Busy Paper Out Select Auto Linefeed * Error * Initialize Printer * Select In * Ground Ground Ground Ground Ground Ground Ground 25 Ground --------------------------------------------------------------------------* = Active low =========================================================================== Table A-2. [. . . ]