User manual HP ARMADA 3500

[. . . ] [. . . ] The computer will generate only those codes applicable to the actual system configuration and installed options. Common Power-On Messages Table A-1 lists the error messages that may occur when the system is powered-on or reset. Table A-1 Power-On Messages Message 163 - Time and date not set (Two very short beeps) RESUME = "F1" key Beeps 2S 2VS None Probable Cause Invalid time or date Power-on successful Any failure Error Messages and Codes A-1 Initialization Diagnostic Messages Table A-2 lists error messages that may occur as part of the Power-On Self-Test (POST). Table A-2 Power-On Self-Test (POST) Messages Message No visible message No visible message 101 - I/O ROM error 101 - ROM error 102 - System Board Failure 102 - System or Memory Board Failure 162 - System Options Error 162 - System Options Not Set (Run SETUP) 163 - Time and Date Not Set 164 - Memory Size Error 170 - Expansion Device not Responding (Run SETUP) 176 - Slot with No Readable ID (Run SETUP) 177 - SETUP Not Complete (Run SETUP) 178 - Processor SETUP Invalid (Run SETUP) XXOOOY ZZ 201 - Memory Error XXOOOY ZZ 203 - Memory Error 205 - Cache Memory Failure Z 205 - Memory Failure 206 - Secondary Cache Controller Failure 207 - Invalid Memory Configuration Z 209 - NCA RAM Error 211 - Memory Failure 301 - Keyboard Error 301 - Keyboard Error or Test Fixture Installed 302 - System Unit Security Lock is Locked - Unlock System Unit Security Lock 303 - Keyboard Controller Error 304 - Keyboard or System Unit Error 401 - Printer Error 401 - Port 1 Address Assignment Conflict 402 - Monochrome Adapter Failure 403 - Port 3 Address Assignment Conflict Beeps 3L 2L 1L, 1S 1L, 1S None None 2S 2S 2S 2S None None None None None None None None None None None None None None 2S None None None 2S 1L, 2S 2S Probable Cause Processor Self-test Memory map failure Option ROM checksum System ROM checksum DMA or timers High-order addresses No diskette drives or mismatch in drive types System SETUP Invalid time or date in configuration memory Memory size discrepancy Expansion device not responding Slot with no readable ID SETUP not complete Processor SETUP invalid RAM failure RAM failure System board Memory board failure Cache Memory Controller Failure System memory board NCA Failure RAM Failure Keyboard failure Keyboard test fixture System locked Keyboard controller Keyboard interface Printer controller External and Internal Port assignments to Port 1 Monochrome display controller External and Internal Port Assignments to Port 1 Graphics display controller 501 - Display Adapter Failure 1L, 2S NOTES: 1. XX000Y ZZ = Address (XX), byte (Y), data bit (ZZ) of failed memory test Continued A-2 Error Messages and Codes Table A-2 Power-On Self-Test (POST) Messages Continued Message 601 - Diskette Drive Controller Error 602 - Diskette Drive Boot Record Error 605 - Diskette Drive Type Error 607 - Diskette Drive Controller Error 611 - Primary Diskette Drive Assignment Conflict 612 - Secondary Diskette Drive Assignment Conflict 702 - A-Coprocessor Detection Error 703 - Coprocessor Detection Error 1125 - Internal Serial Port Failure 1150 - xx Comm Port Setup Error 1151 - COM1 Address Assignment Conflict 1152 - COM2 Address Assignment Conflict 1153 - COM3 Address Assignment Conflict 1153 - COM4 Address Assignment Conflict Beeps None None 2S 2S 2S 2S 2S 2S 2S 2S 2S 2S 2S 2S Probable Cause Diskette drive controller Diskette drive does not have a valid boot record Wrong drive type used in the computer setup utility Configuration error Configuration error Configuration error Add coprocessor or configuration error Add coprocessor or configuration error Defective internal serial port Setup not correct (run SETUP) External and internal port assignments to COM1 External and internal port assignments to COM2 External and internal port assignments to COM3 External and internal port assignments to COM4 Configuration mismatch 1600 - 32-Bit System Manager Board 2S Failure 1730 - Hard Drive 0 Does Not Support 2S Configuration mismatch DMA Mode 1731 - Hard Drive 1 Does Not Support 2S Configuration mismatch DMA Mode 1740 - Hard Drive 0 Failed Set Block Mode 2S Configuration mismatch Command 1741 - Hard Drive 1 Failed Set Block Mode None Wrong drive type Command 1750 - Hard Drive 0 Failed Identify None Wrong drive type Command 1751 - Hard Drive 0 Failed Identify None Wrong drive type Command 1760 - Hard Drive 0 Does Not Support 2S Configuration mismatch Block Mode 1761 - Hard Drive 1 Does Not Support 2S Configuration mismatch Block Mode 1771 - Primary Drive Port Address 2S Internal and external hard drive controllers Assignment Conflict assigned to primary address 1772 - Secondary Disk Port Address Internal and external hard drive controllers Assignment Conflict assigned to secondary address 1780 - Hard Drive 0 Failure None Hard drive 0 not ready 1781 - Hard Drive 1 Failure 2S Hard drive 1 not ready 1782 - Hard Drive Controller Failure None Hard drive controller NOTES: 1. XX000Y ZZ = Address (XX), byte (Y), data bit (ZZ) of failed memory test Continued Error Messages and Codes A-3 Table A-2 Power-On Self-Test (POST) Messages Continued Message Beeps Probable Cause 1790 - Hard Drive 0 Error None Wrong drive type used in SETUP 1791 - Hard Drive 1 Error None Wrong drive type used in SETUP 1792 - Secondary Drive Controller Error None hard drive error or wrong drive type 1793 - Secondary Controller or Drive None hard drive error or wrong drive type Failure XX000Y ZZ Parity Check 2 None RAM parity failure Hard Drive Parameter Table or BIOS Error 3L Configuration or hardware failure IOCHECK Active, Slot X None Defective board in slot x Bus Master Time-Out Slot X None Defective board in slot x Audible 1S Power-On successful Audible 2S Power-On successful (RESUME = "F1" KEY) None As indicated to continue NOTES: 1. XX000Y ZZ = Address (XX), byte (Y), data bit (ZZ) of failed memory test A-4 Error Messages and Codes Advanced Diagnostics Error Messages The following tables list error messages that may occur during Advanced Diagnostics testing. [. . . ] [. . . ]