User manual HP BLADESYSTEM BC1500 BLADE PC

[. . . ] User Guide HP BladeSystem PC Blade Enclosure Integrated Administrator for CCI v1. 4 Document Part Number: 410728-002 June 2006 © Copyright 2005, 2006 Hewlett-Packard Development Company, L. P. The information contained herein is subject to change without notice. Microsoft, MS-DOS, Windows, and Windows NT are trademarks of Microsoft Corporation in the U. S. Intel, Pentium, Intel Inside, and Celeron are trademarks of Intel Corporation in the U. S. [. . . ] Displays the status, redundancy, and partner, speed, part number for the requested fan. If ALL is entered, this information is shown for all fans. Displays the enclosure name, type, part number, serial number, and asset tag; the Integrated Administrator software and hardware version; Integrated Administrator MAC address, and the interconnect tray type, part number, and serial number Only the enclosure administrators may execute this command. None SHOW DISPLAY SHOW ENCLOSURE FAN [<fan number> | ALL] SHOW ENCLOSURE INFO None None None HP PC Blade Enclosure Integrated Administrator for CCI v1. 4 User Guide 5-13 Command Line Interface Enclosure Management Commands (continued) Command SHOW ENCLOSURE POWER SUPPLY [<power supply number> | ALL] Description Restrictions Displays the power supply status, AC input status, capacity, input voltage range #1 (measured in Volts), input voltage range #2 (if necessary, measured in Volts), input frequency range (measured in Hertz), part number, serial number, and hardware revision for the specified power supply if one is specified or for all power supplies if ALL is given. Under an enclosure status heading, this command displays the health, Integrated Administrator health, and unit identification LED of the enclosure. Under a power status heading, this command displays the power status and capacity. None SHOW ENCLOSURE STATUS None SHOW ENCLOSURE TEMP SHOW RACK NAME <rack name> SHOW SYSLOG ENCLOSURE Displays the locale, status (OK, warm, degraded, or failed), temperature in degrees Fahrenheit, and temperature sensors. Shows the name for the rack where the enclosure resides The default rack name is UnnamedRack. Displays the syslog of the enclosure with 22 lines per screen. Typing q quits the command, any other key shows the next screen if more information exists to display. Typing c continuously displays the System Log without page breaks. None None Only enclosure administrators may execute this command. SHOW TRAY INFO Displays the manufacturer, product name, part number, serial number, and spare number of the interconnect tray. None 5-14 HP PC Blade Enclosure Integrated Administrator for CCI v1. 4 User Guide Command Line Interface Enclosure Management Commands (continued) Command UPDATE IMAGE <url> Description Restrictions Downloads a new image from a blade over the network and uses the image to update the firmware of the enclosure. Only enclosure administrators may execute this command. URL can be any of the following: · http://host/path · tftp://host/path · ftp://username:password · @host/path · ftp://host/path where host is a fully qualified domain name or an IP address and path is the pathname of the flash image to download UPLOAD CONFIG <url> Upload the current runtime configuration to the specified FTP or TFTP server. Only enclosure administrators may execute this command. Blade PC Bay Management Commands Blade PC Bay Management Commands Command CLEAR BAY BOOT [FIRST | ONCE | ALWAYS] [ALL | <bay number> {[ , | ] <bay number>}] Description Restrictions Clears the setting for the IPL to be passed to the blade at the next reboot. The FIRST argument resets the IPL for all subsequent reboots. The ONCE argument resets the IPL for the next reboot only. The Always argument resets the IPL for every reboot. This command is only valid for present blades. This command may require a firmware update for the BIOS ROM of certain HP blade PCs. Only enclosure and group administrators may execute this command. CLEAR SESSION BAY <bay number> CONNECT BAY <bay number> Terminates a Terminal session from the enclosure. The connected user loses any unsaved work. Opens a remote console session to the blade PC with that blade PC bay number. A blade PC can only support one remote console session at a time. Enclosure administrators may execute this command for blade PC bays and the interconnect switch. Only enclosure and group administrators may execute this command. HP PC Blade Enclosure Integrated Administrator for CCI v1. 4 User Guide 5-15 Command Line Interface Blade PC Bay Management Commands (continued) GENERATE NMI <bay number> POWEROFF BAY <bay number> {[ , | - ] <bay number>} {FORCE} POWERON BAY <bay number> {[ , | - ] <bay number>} {[PXE | HDD | RBSU]} Generates an NMI on the specified blade. The consequences of an NMI are operating system specific. Performs a graceful shutdown of the blade PC in the specified bay. [. . . ] If the problem continues, contact the enclosure administrator. Everything ran as expected. The Integrated Administrator supports up to 48 concurrent sessions. Be sure the number of sessions has not reached this threshold and check with an enclosure administrator to be sure your account is not disabled. The Event list only displays negative events that happen during the user's login session. [. . . ]