User manual HP CISCO CATALYST BLADE SWITCH 3120G AND CISCO CATALYST BLADE SWITCH 3120X FOR CISCO CATALYST BLADE SWITCH 3120 FOR COMMAND REFERENCE

[. . . ] Cisco Catalyst Blade Switch 3120 for HP Command Reference Cisco IOS Release 12. 2(40)EX November 2007 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www. cisco. com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Text Part Number: OL-12248-01 THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS. [. . . ] The switch cannot filter source MAC addresses. · This is an example of output on an interface on which IP source guard is disabled: Switch> show ip verify source gigabitethernet1/0/6 IP source guard is not configured on the interface gi1/0/6. Related Commands Command ip verify source Description Enables IP source guard on an interface. Cisco Catalyst Blade Switch 3120 for HP Command Reference 2-486 OL-12248-01 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ipc show ipc Use the show ipc user EXEC command to display Interprocess Communications Protocol (IPC) configuration, status, and statistics on a switch stack or a standalone switch. show ipc {mcast {appclass | groups | status} | nodes | ports [open] | queue | rpc | session {all | rx | tx} [verbose] | status [cumlulative] | zones} [ | {begin | exclude | include} expression] Syntax Description mcast {appclass | groups | status} Display the IPC multicast routing information. The keywords have these meanings: · · · appclass--Display the IPC multicast application classes. groups--Display the IPC multicast groups. status--Display the IPC multicast routing status. nodes ports [open] queue rpc Display participating nodes. The keyword has this meaning: · open--(Optional) Display only the open ports. Display the contents of the IPC transmission queue. Display the IPC remote-procedure statistics. session {all | rx | tx} Display the IPC session statistics (available only in privileged EXEC mode). The keywords have these meanings: · · · all--Display all the session statistics. rx--Display the sessions statistics for traffic that the switch receives tx--Display the sessions statistics for traffic that the switch forwards. verbose (Optional) Display detailed statistics (available only in privileged EXEC mode). · status [cumlulative] Display the status of the local IPC server. The keyword has this meaning: cumlulative--(Optional) Display the status of the local IPC server since the switch was started or restarted. zones | begin | exclude | include expression Display the participating IPC zones. (Optional) Display begins with the line that matches the expression. (Optional) Display excludes lines that match the expression. (Optional) Display includes lines that match the specified expression. Expression in the output to use as a reference point. Command Modes User EXEC Command History Release 12. 2(40)EX Modification This command was introduced. Cisco Catalyst Blade Switch 3120 for HP Command Reference OL-12248-01 2-487 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ipc Usage Guidelines Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output do not appear, but the lines that contain Output appear. Examples This example shows how to display the IPC routing status: Switch> show ipc mcast status IPC Mcast Status Tx Total Total Total Total Total Total Total Total Frames control Frames Frames dropped control Frames dropped Reliable messages Reliable messages acknowledged Out of Band Messages Out of Band messages acknowledged 0 0 0 0 0 0 0 0 0 0 0 0 Total Timeouts Total OOB Timeouts Total No ports Rx 0 0 0 0 0 0 0 0 0 0 0 0 Total No Mcast groups Total Retries Total OOB Retries Total flushes This example shows how to display the participating nodes: Switch> show ipc nodes There is 1 node in this IPC realm. ID Type Name Last Sent 10000 Local IPC Master 0 Last Heard 0 This example shows how to display the local IPC ports: Switch> show ipc ports There are 8 ports defined. Port ID Type Name (current/peak/total) There are 8 ports defined. 10000. 1 unicast IPC Master:Zone 10000. 2 unicast IPC Master:Echo 10000. 3 unicast IPC Master:Control 10000. 4 unicast IPC Master:Init 10000. 5 unicast FIB Master:DFS. process_level. msgs 10000. 6 unicast FIB Master:DFS. interrupt. msgs 10000. 7 unicast MDFS RP:Statistics port_index = 0 seat_id = 0x10000 last sent = 0 last heard = 0 0/2/159 10000. 8 unicast Slot 1 :MDFS. control. RIL port_index = 0 seat_id = 0x10000 last sent = 0 0/0/0 RPC packets:current/peak/total 0/1/4 last heard = 0 Cisco Catalyst Blade Switch 3120 for HP Command Reference 2-488 OL-12248-01 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ipc This example shows how to display the contents of the IPC retransmission queue: Switch> show ipc queue There are 0 IPC messages waiting for acknowledgement in the transmit queue. There are 0 IPC messages waiting for a response. There are 0 IPC messages waiting for additional fragments. There are 0 IPC messages currently on the IPC inboundQ. Messages currently in use : 3 Message cache size : 1000 Maximum message cache usage : 1000 0 times message cache crossed 5000 [max] : 0 Emergency messages currently in use There are 2 messages currently reserved for reply msg. [. . . ] multicast-expansion--Display the IPv6 multicast-expansion table. vlan-list--Display the VLAN list table. usage Display the CAM and forwarding table usage. [[asic number [detail [invalid]] | Display information. The keywords have these meanings: [index number [detail [invalid]] | · asic number--Display information for the specified ASIC invalid | num number [detail device ID. [invalid]] | invalid] | [invalid] | [num number [detail [invalid]] | · detail [invalid]--(Optional) Display valid or invalid details. [. . . ]