User manual HP COLOR LASERJET 2605

[. . . ] HP Color LaserJet 2605, 2605dn, 2605dtn User Guide HP Color LaserJet 2605, 2605dn, and 2605dtn Printer User Guide Copyright and License © 2006 Copyright Hewlett-Packard Development Company, L. P. Reproduction, adaptation, or translation without prior written permission is prohibited, except as allowed under the copyright laws. The information contained in this document is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. [. . . ] Insert enough paper into Tray 2 or optional Tray 3 to accommodate the print job. NOTE In Windows, Print on both sides (manually) must be enabled to complete these instructions. To enable duplexing, in the printer driver, select Properties, and then click on the Configure tab. Under Paper handling, select Allow Manual Duplexing, and then click OK to save. ENWW Print: How do I? 95 2. Use the following procedure to configure the printer to Print on both sides (manually). In the printer driver, select the Finishing tab, select the Print on both sides (manually) option, and then send the job to print. 3. After the job is finished printing, remove any blank paper as prompted by the control panel. Lift the printed stack from the output bin and insert the printed stack without rotating or turning the stack over into the printer tray that was used for the first part of the job. A 4. Press (Select) to continue printing on the second side. To print on both sides (automatically) Perform the following steps to print on both sides (automatically). To check for supported media for 2­sided printing, see Print-media specifications. Verify that the printer driver is configured for 2­sided printing. For instructions, see the online help for the printer driver. Select the appropriate 2­sided printing options in the printer driver software, including page and binding orientation. NOTE When using 2­sided printing, load pre-printed forms and letterhead into Tray 1 faceup with the bottom edge of the page feeding first. Load preprinted forms and letterhead into Tray 2 and Tray 3 face-down with the top edge at the back of the tray. NOTE Loading pre-printed forms and letterhead is different than loading for 1­sided printing. 96 Chapter 9 How do I? ENWW Select paper type for special media Use the guidelines in following table when printing on special media. If printing on a special type of media, printing speeds might be automatically reduced to improve the output quality for that specific media. See Print-media specifications for media that is recommended for this printer. For instruction on loading the trays, see Loading Tray 1 or Loading Tray 2. Table 9-1 Special media printing guidelines Paper type Maximum amount that can be loaded into Tray 2 or optional Tray 3 Up to 250 sheets Up to 10 envelopes Paper quality, type Tray 1 paper orientation Tray 2 or optional Tray 3 paper orientation Normal Envelopes Plain or unspecified Envelope Side to be printed face down Short edge leading, flap on right side facing down Short edge leading, flap on right side facing down Side to be printed face down Side to be printed face down Side to be printed face down Side to be printed face down, printed edge at front of tray Side to be printed face down Side to be printed face up Short edge leading, flap on right side facing up Short edge leading, flap on right side facing up Side to be printed face up Side to be printed face up Side to be printed face up Side to be printed face up, printed edge at front of tray Side to be printed face up Heavy envelopes Up to 10 envelopes Heavy envelope Labels Transparencies Glossy Letterhead Up to 25 mm Labels (0. 99 inch) stack height Up to 50 sheets Transparencies Up to 25 mm Light glossy, glossy, (0. 99 inch) stack height or heavy glossy Up to 250 sheets Letterhead Cardstock Up to 25 mm Cardstock or heavy (0. 99 inch) stack height Change the device print settings, such as print quality, in HP ToolboxFX To change the default print settings in HP ToolboxFX, complete the following steps. NOTE The changes that you make to the print settings in HP ToolboxFX apply to all future print jobs. Open HP ToolboxFX and click Device Settings. On the Settings tab, you can modify settings that appear on the following pages. Paper Handling Printing Print Quality ENWW Print: How do I? 97 4. Print Density Paper type settings Print Modes System Setup Service Click Apply to save the changes that you make on these pages. NOTE If you have similar settings in the printer driver, those settings take priority over the settings that are established in HP ToolboxFX. Print color documents from my computer in black and white only In the software program, select File, Print, the HP Color LaserJet 2605 or HP Color LaserJet 2605_dtn PCL6 print driver, click Properties, click the Color tab, and then select the Print in Grayscale check box. Click OK to save the print properties, and then click OK again to print the document. Change color options Use the Manual color adjustment to adjust the Color (or Color Map) options. NOTE Some software programs convert text or graphics to raster images. In these cases, the Photographs setting also controls the text and graphics. Halftone options Halftoning is the method by which the printer mixes the four primary colors (cyan, magenta, yellow, and black) in varying proportions to create millions of colors. Halftone options affect the resolution and clarity of your color output. [. . . ] 3) For regulatory purposes, this product is assigned a Regulatory model number. This number should not be confused with the product name or the product number(s). Boise, Idaho, USA 22 December, 2005 For regulatory topics only: Australia Contact: European Contact: USA Contact: Product Regulations Manager, Hewlett-Packard Australia Ltd. , 31-41 Joseph Street, Blackburn, Victoria 3130, Australia. Your Local Hewlett-Packard Sales and Service Office or Hewlett-Packard Gmbh, Department HQ-TRE / Standards Europe, Herrenberger Strasse 140, D-71034 Böblingen, Germany (FAX: +49-7031-14-3143) Product Regulations Manager, Hewlett-Packard Company, PO Box 15, Mail Stop 160, Boise, Idaho 83707-0015, USA (Phone: 208-396-6000) ENWW Declaration of conformity 203 Country/region-specific safety statements Laser safety statement The Center for Devices and Radiological Health (CDRH) of the U. S. [. . . ]