User manual HP COLOR LASERJET CM1312 MFP

[. . . ] HP Color LaserJet CM1312 MFP Series User Guide HP Color LaserJet CM1312 MFP Series User Guide Copyright and License © 2008 Copyright Hewlett-Packard Development Company, L. P. Reproduction, adaptation, or translation without prior written permission is prohibited, except as allowed under the copyright laws. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. [. . . ] This allows you to wait for pauses, dial tones, international-access tones, or calling-card-acceptance tones before continuing to dial. ENWW Use fax 129 Dial manually with the flatbed scanner 1. The control-panel display shows the following message: Send from flatbed scanner?. The control-panel display shows the following message: Load page: X Press OK, where X is the page number. Scan a page into memory by placing the sheet print-side-down on the flatbed scanner and pressing OK. After scanning the page, the product control-panel display shows the following message: Scan another page?. If you have more pages to scan, select Yes, and then repeat step 3 for each page of the fax job. -orIf you are finished, select No, and then go to the next step. When all pages are scanned into memory, begin dialing. The product dials the number as you press each digit. This allows you to wait for pauses, dial tones, international access tones, or calling card acceptance tones before continuing to dial. 4. Send a fax to a group manually (ad hoc faxing) Use the following instructions to send a fax to a group of recipients that has not been assigned a groupdial entry: 1. Load the document into the automatic document feeder (ADF) input tray or on the flatbed scanner. -orIf the fax number that you are calling has been assigned a speed-dial entry, press Fax Menu, then select Phone Book. Choose Select an entry and use the alphanumeric buttons to specify the speed-dial entry, and then press OK. To continue dialing numbers, repeat steps 2 and 3. -orIf you are finished dialing numbers, go to the next step. If the pages that you want to send are in the ADF, then faxing begins automatically. If the product ADF sensor detects that no document is loaded into the ADF input tray, Send from flatbed scanner?To send the fax from the flatbed scanner, select Yes, and then press OK. Load Page: X Press OK appears on the control-panel display. If you have already placed the document on the flatbed scanner, press OK (or place the document on the flatbed scanner and then press OK). If you have more pages to scan, select Yes, and then repeat step 7 for each page of the fax job. 130 Chapter 12 Fax (fax models only) ENWW -orIf you are finished, select No. The product sends the fax to each fax number. [. . . ] This number should not be confused with the product name or the product number(s). 3) Telecom approvals and standards appropriate for the target countries/regions have been applied to this product, in addition to those listed above. 4. ) This product uses an analog fax accessory module which Regulatory Model numbers are: BOISB-0704-00 (US-LIU) or BOISB-0704-01 (EURO LIU), as needed to meet technical regulatory requirements for the countries/regions this product will be sold. Boise, Idaho , USA December 2007 For regulatory topics only: European Contact: Your Local Hewlett-Packard Sales and Service Office or Hewlett-Packard GmbH, Department HQ-TRE / Standards Europe, , Herrenberger Straße 140, D-71034 Böblingen, Germany, (FAX: +49-7031-14-3143), http://www. hp. com/go/ certificates USA Contact: Product Regulations Manager, Hewlett-Packard Company, , PO Box 15, Mail Stop 160, Boise, ID 83707-0015, , (Phone: 208-396-6000) ENWW Declaration of conformity 249 Country/region specific statements Laser safety The Center for Devices and Radiological Health (CDRH) of the U. S. [. . . ]