User manual HP COMPAQ PRESARIO SR1800

[. . . ] COMPAQ, the Compaq logo, and Deskpro Registered in U. PREMIER·SOUND is a trademark of Compaq Computer Corporation. Microsoft, MS-DOS, Windows, Windows NT, and other names of Microsoft products referenced herein are trademarks or registered trademarks of Microsoft Corporation. Intel and Pentium are registered trademarks of Intel Corporation. [. . . ] DMTF established the Desktop Management Interface (DMI) framework to standardize access to PC configuration data. Compaq, as a Steering Committee and Technical Committee member of the DMTF, delivers hardware and software instrumentation that supports the DMI standard. For more information on configuring the DMI software, refer to the online Intelligent Manageability Guide. 3. 5. 2 Wired for Management Intel's Wired for Management initiative is focused on reducing the support and administration cost of Intel architecture-based systems without compromising their flexibility and performance. The Wired for Management guidelines provide a baseline set of building blocks that Compaq utilizes in Intelligent Manageability to provide standardized management of desktop inventories, remote system configuration, off-hours maintenance, and next generation power management. But Compaq doesn't stop with these baseline features. Additional capabilities have been incorporated into Intelligent Manageability to provide an extensive solution for managing networked computing environments. Required Wired for Management technologies include: !"Desktop Management Interface (DMI) 2. 0 !"Remote System Installation !"Remote Wakeup and Remote Shutdown !"ACPI-Ready Hardware !"SMBIOS !"Pre-boot execution (PXE) support Compaq Service Reference Guide 3-19 chapter 4 Device Class Class 2 Magnetic Storage 2. 1 LS-120 2. 2 Tape Drive 2. 3 Iomega Zip Drive IDE/ATAPI DEVICE SEQUENCING GUIDELINES This guideline standardizes the configuration of multiple IDE/ATAPI storage devices. It categorizes the devices by the type of media used and then ranks the device within each class. Class 1 Hard Drives Class 3 Optical Storage 3. 1 R/W CD-ROM Drive 3. 2 DVD-ROM Drive 3. 3 CD-ROM Drive 4. 1 General Application Rules 1. When possible, hard drives should be configured by themselves on the primary controller channel. When devices from all three classes are present, class 2 and 3 devices should be combined first on the secondary controller channel. When combining two devices on any controller channel, the device with the lower rank should be the primary device (master) and the higher rank the secondary device (slave). 1 through 6 and 8 through 15 are available for all other SCSI devices. !"Every SCSI chain or circuit must be terminated (closed) at both ends. Some system boards have both ends of the SCSI cable connected to, and terminated by, the system board. Termination can be accomplished in one of several ways: Use a cable with a built-in terminator. Use a cable with a terminating resistor plug in the last connector. Connect a SCSI device with its termination enabled into the last connector. Connect an external SCSI device with its termination enabled to the external SCSI connector on the rear panel of the computer. Compaq Service Reference Guide 5-1 !"For workstations, if only one SCSI hard drive is used, it should be installed in the lowest numbered bay (bay 1). (Refer to the product-specific MSG for application). !"All SCSI hard drives must be either internal or external, but never both. The system accommodates a combination of other internal and external SCSI devices, such as tape and CD-ROM drives. !"Turn on all external SCSI devices before turning on the power to the computer. This enables the SCSI controller to recognize the external devices. Using the Multi-Mode SCSI Cable Some products ship standard with a three-device multi-mode SCSI cable having a terminator 1 on one end. This cable supports both low voltage differential (LVD) and single ended (SE) devices. One end of the cable connects to the internal LVD/SE connector on the system board, while the remaining three connectors being used on the hard drives in the hard drive bays. [. . . ] Run Computer Setup or Windows NT, Windows 95, or Windows 98 utilities. Replace the system board. * Ethernet only. ** Token Ring only. CD-ROM and DVD-ROM Error Code 3301-xx 3305-xx 6600-xx 6605-xx 6608-xx 6623-xx Description CD-ROM drive read test failed. Random read test failed. Recommended Action The following steps apply to 3301-xx through 3305-xx and 6600-xx through 6623-xx: 1. [. . . ]