User manual HP COMPAQ PROLIANT 1200 SERVER

[. . . ] IDE CD-ROM Drive for Servers and Workstations Installation and User Guide Second Edition (November 1997) Part Number 242699-002 Compaq Computer Corporation Notice The information in this publication is subject to change without notice. COMPAQ COMPUTER CORPORATION SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN, NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL. THIS INFORMATION IS PROVIDED "AS IS" AND COMPAQ COMPUTER CORPORATION DISCLAIMS ANY WARRANTIES, EXPRESS, IMPLIED OR STATUTORY AND EXPRESSLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE, GOOD TITLE AND AGAINST INFRINGEMENT. This publication contains information protected by copyright. [. . . ] Preparing your system so that you have access to the removable media drive bays. s Refer to the documentation included with your system for detailed instructions on performing these tasks. Once you have prepared the system, complete the following steps to install your optional IDE CD-ROM drive: 1. Slide the drive into the bay and secure it. Connect the IDE and power cables. IDE CD-ROM Drive for Servers and Workstations Installation and User Guide 2-6 Installing an Optional CD-ROM Drive Installation Sequence Step 1 - Setting the Jumpers CAUTION: Electrostatic discharge (ESD) can damage electronic components. Be sure you are properly grounded before beginning this procedure. See Appendix B, "Electrostatic Discharge" for further information. Make sure that the jumpers on the rear of the drive match the settings indicated in Table 2-3. 123 Figure 2-1. Default Jumper Setting on a Compaq IDE CD-ROM Drive IDE CD-ROM Drive for Servers and Workstations Installation and User Guide 2-7 Installing an Optional CD-ROM Drive Table 2-3 Jumpers on a Compaq IDE CD-ROM Drive Reference Description CS - Cable select for device 0 or device 1 SL - Device 1 (Secondary/slave device) MA - Device 0 (Primary device) Setting Enabled, installed over both pins Disabled, not installed Disabled, not installed Although the Compaq IDE CD-ROM drive is set for cable select, the IDE Interface Cables included in this option kit do not support cable select. If you must use one of these cables, use the table above to set the jumpers on the drive to Device 1 (secondary/slave) or Device 0 (primary), as appropriate for your system. IDE CD-ROM Drive for Servers and Workstations Installation and User Guide 2-8 Installing an Optional CD-ROM Drive Step 2 - Installing the Drive Rails If your system requires drive rails, attach the two rails in this kit with the four screws provided (two screws for each side). COMPACT Figure 2-2. Attaching Drive Rails to a Compaq IDE CD-ROM Drive IDE CD-ROM Drive for Servers and Workstations Installation and User Guide 2-9 Installing an Optional CD-ROM Drive Step 3 - Inserting the Drive Horizontal Orientation Position the drive on the drive guides, then slide it into the drive bay, as indicated. COMPA CT Figure 2-3. Inserting the CD-ROM Drive into a Horizontal Drive Bay IDE CD-ROM Drive for Servers and Workstations Installation and User Guide 2-10 Installing an Optional CD-ROM Drive Vertical Orientation Position the drive on the drive guides, then slide it into the drive bay, as indicated. Figure 2-4. Inserting the CD-ROM Drive into a Vertical Drive Bay Securing the Drive Secure the drive to the computer with the 2 retaining screws provided in this kit, or with the retaining screws from the front bezel. Step 4 - Connecting the Cables If a 2-device IDE cable was not shipped with your system, use one of the 2-device IDE cables supplied with this kit to connect your IDE devices. These cables are identical, except in length. It is a good idea to save your 1-device IDE cable for future use. Note the position of each connector on the IDE interface cable supplied with your kit, as indicated in Figure 2-5. IDE CD-ROM Drive for Servers and Workstations Installation and User Guide 2-11 Installing an Optional CD-ROM Drive 2 1 3 Figure 2-5. IDE Interface Cable Connectors Table 2-4 IDE Interface Cable Connectors Reference Connector System board connector Secondary drive connector (Device 1) Primary drive connector (Device 0) Connector is for the secondary drive (device 1); connector is for the primary drive (device 0). Connect the hard drive to cable connector and the CD-ROM drive to cable connector . Connect the power and IDE interface cables to the drive, as indicated in Figure 2-6. IDE CD-ROM Drive for Servers and Workstations Installation and User Guide 2-12 Installing an Optional CD-ROM Drive 1 2 3 Figure 2-6. Connecting the Drive Cables Table 2-5 Drive Cable Connections Reference Audio connector IDE connector Power connector Connector If you are installing this IDE drive as the primary drive and your system has audio capabilities, attach the audio cable supplied with your system to the audio connector on the CD-ROM drive. IDE CD-ROM Drive for Servers and Workstations Installation and User Guide 2-13 Installing an Optional CD-ROM Drive Completing the Installation To complete the installation: 1. Reassemble your system according to the documentation that shipped with it. Reconnect the peripheral devices to the system. Plug the power cord into the computer, then into a properly grounded electrical outlet. Configuring Your New Drive No special driver or software support is needed if you are replacing a drive of the same type, or if you are installing a CD-ROM drive in addition to an existing drive of the same type. Run the System Configuration Utility according to the documentation provided with your system to make sure the drive has been recognized and properly configured. If this IDE CD-ROM drive is of a different type than the one installed, or if it is a new IDE device, see Appendix D, "Getting Help, " for information on how to contact Compaq or an authorized representative to determine if you need an additional driver for your system configuration. See Chapter 3, "Operating the Drive, " in this guide for instructions on how to use your IDE CD-ROM drive. IDE CD-ROM Drive for Servers and Workstations Installation and User Guide 3-1 Operating the Drive Chapter 3 Operating the Drive This chapter outlines the basic functions of your new Compaq IDE CD-ROM Drive. Front Panel Controls The following controls are located on the front panel. 4 1 2 3 COMPACT 5 Figure 3-1. Front Panel Controls on a Compaq IDE CD-ROM Drive Table 3-1 Front Panel Controls for a Compaq IDE CD-ROM Drive Ref Component Busy Indicator Headphone Volume Control Headphone Jack Disc Slot Eject Button Function Turns amber when drive runs diagnostics Increases or decreases the headphone volume Connects the headphone Accepts and ejects the CD-ROM disc Ejects the CD-ROM disc IDE CD-ROM Drive for Servers 3-2 Operating the Drive Loading a Disc Use the following steps to load a compact disc in the drive: 1. The busy indicator on the CD-ROM drive illuminates. Holding the disc by the edges, not by the flat surfaces of the disc, slide it label side up into the drive. [. . . ] Compliance is mandatory for products marketed in the United States. Compliance with International Regulations All Compaq systems equipped with CD-ROM drives comply with appropriate safety standards including IEC 825. IDE CD-ROM Drive for Servers and Workstations Installation and User Guide A-7 Regulatory Compliance Notices Laser Product Label The following label or equivalent is located on the surface of your CD-ROM drive. This label indicates that the product is classified as a CLASS 1 LASER PRODUCT. This label appears on a laser device installed in your product. Laser Information Laser Type Wave Length Divergence Angle Output Power Polarization Numerical Aperture Semiconductor GaAIAs 780 nm +/- 35 nm 53. 5 degrees +/- 0. 5 degrees Less than 0. 2 mW /10, 869 W·m sr Circular 0. 25 0. 45 inches +/- 0. 04 inches -2 -1 IDE CD-ROM Drive for Servers and Workstations Installation and User Guide A-8 Regulatory Compliance Notices IDE CD-ROM Drive for Servers and Workstations Installation and User Guide B-1 Electrostatic Discharge Appendix B Electrostatic Discharge To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device. [. . . ]