User manual HP COMPAQ PRESARIO V5155EA

[. . . ] b Maintenance and Service Guide Compaq Presario V5100 Notebook PC Document Part Number: 407368-001 February 2006 This guide is a troubleshooting reference used for maintaining and servicing the computer. It provides comprehensive information on identifying computer features, components, and spare parts; troubleshooting computer problems; and performing computer disassembly procedures. © Copyright 2006 Hewlett-Packard Development Company, L. P. registered trademarks of Microsoft Corporation. Intel and Pentium are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. [. . . ] 0 5. 8 RTC Battery Maintenance and Service Guide 5­3 Removal and Replacement Procedures Disassembly Sequence Chart (Continued) Section 5. 9 Description Optical Drive # of Screws Removed 1 to remove the optical drive, 2 to remove the optical drive bracket 2 4 6 to remove the display assembly 6 to remove the display bezel 2 to remove the display hinge base covers 4 to remove the display panel 2 to remove the display release hook 4 to remove each display hinge 1 to remove each wireless antenna transceiver 18 2 4 6 2 10 1 loosened 2 2 5. 10 5. 11 5. 12 Switch Cover Keyboard Display Assembly 5. 13 5. 14 5. 15 5. 16 5. 17 5. 18 5. 19 5. 20 5. 21 Base Enclosure Bluetooth Module System Board Display Release Button Assembly LED Board Fan/Heat Sink Assembly Processor PC Card Assembly ExpressCard Assembly 5­4 Maintenance and Service Guide Removal and Replacement Procedures 5. 3 Preparing the Computer for Disassembly Before you begin any removal or installation procedures: 1. If you are unsure whether the computer is off or in hibernation, turn the computer on, and then shut it down through the operating system. Disconnect all external devices connected to the computer. Disconnect the power cord. Battery Pack Spare Part Number Information 12-cell, 8. 8-Amp hour 6-cell, 4. 0-Amp hour 407835-001 407834-001 Maintenance and Service Guide 5­5 Removal and Replacement Procedures 4. Remove the battery pack by following these steps: a. Turn the computer upside down with the front toward you. Slide the battery pack release latch 1 to the left. (The battery pack disengages from the computer. ) c. Lift the front edge of the battery pack 2 and swing it back to remove it. Removing the Battery Pack Reverse the above procedure to install the battery pack. 5­6 Maintenance and Service Guide Removal and Replacement Procedures 5. 4 Hard Drive Hard Drive Spare Part Number Information 5400 rpm, 100-GB 5400 rpm, 80-GB 5400 rpm, 60-GB 5400 rpm, 40-GB 409064-001 409063-001 409062-001 409061-001 1. Prepare the computer for disassembly (refer to Section 5. 3). Loosen the two Phillips PM2. 5×5. 0 captive screws 1 that secure the hard drive cover to the computer. Lift the rear edge of the hard drive cover 2, and then swing it up and forward and remove it. is included in the Plastics Kit, spare part number Removing the Hard Drive Cover Maintenance and Service Guide 5­7 Removal and Replacement Procedures 4. Slide the hard drive 1 to the right, and then lift the hard drive 2 from the hard drive bay. Removing the Hard Drive 5­8 Maintenance and Service Guide Removal and Replacement Procedures 5. Remove the four Phillips PM3. 0×4. 0 hard drive frame screws 1 that secure the hard drive frame to the hard drive. Slide the hard drive 2 away from the hard drive to remove it. Removing the Hard Drive Frame Reverse the above procedure to reassemble and install the hard drive. Maintenance and Service Guide 5­9 Removal and Replacement Procedures 5. 5 Computer Feet The computer feet are adhesive-backed rubber pads. The feet are included in the Plastics Kit, spare part number 415691-001. that are installed on the There are two additional computer feetfeet are not depicted in 12-cell battery pack. These additional the following image. Replacing the Computer Feet 5­10 Maintenance and Service Guide Removal and Replacement Procedures 5. 6 Memory Module Memory Module Spare Part Number Information Memory modules (1 DIMM) PC2-5300 1024 MB 512 MB 256 MB 409060-001 409059-001 409058-001 PC2-4200 1024 MB 512 MB 256 MB 407767-001 407766-001 407765-001 1. Prepare the computer for disassembly (refer to Section 5. 3). Maintenance and Service Guide 5­11 Removal and Replacement Procedures 2. Loosen the Phillips PM2. 5×5. 0 captive screw 1 that secures the memory/Mini Card module compartment cover to the computer. Lift the right side of the cover 2 and swing it up and to the left and remove it. [. . . ] Specific details, such as screw sizes, quantities, and locations, and component shapes and sizes, can vary from one computer model to another. Refer to Section 5. 12, "Display Assembly, " for display assembly disassembly steps. D­2 Maintenance and Service Guide Display Component Recycling Perform the following steps to disassemble the display assembly: 1. Remove all screw covers 1 and screws 2 that secure the display bezel to the display assembly. Removing the Display Bezel Screw Covers and Screws Maintenance and Service Guide D­3 Display Component Recycling 2. Lift up and out on the left and right inside edges 1 and the top and bottom inside edges 2 of the display bezel until the bezel disengages from the display assembly. [. . . ]