User manual HP CONSUMER 20 INCH FLAT PANEL

[. . . ] HP w20 / w22 LCD Monitor User's Guide · · · · · · · · · Preface Safety and Maintenance Guidelines Setup Using the Monitor Installing Drivers and Using the Auto-Adjustment Feature Technical Support FAQs Specifications LCD Monitor Quality and Pixel Policy Agency Regulatory Notices The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. HP assumes no responsibility for the use or reliability of its software on equipment that is not furnished by HP. [. . . ] Set the resolution (Setting the Optimal Resolution) and adjust the volume (Adjusting the Volume). Adjust the onscreen display (OSD) settings (Adjusting OSD Settings). 10 External Controls A B C D E F G ­ (Minus) button + (Plus) button Menu button Source button Auto button Power button Power LED Navigates backward through the OSD menu and decreases adjustment levels. If the OSD menu is inactive, activates the Volume decrease. Navigates forward through the OSD menu and increases adjustment levels. If the OSD menu is inactive, activates the Volume increase. Automatically fine-tunes the image quality. Fully powered = green Sleep mode = amber Sleep timer mode = flashing amber See Technical Support FAQs for more information. 11 Back to Contents Page Settings Setting the Optimal Resolution · Adjusting the Volume · Locking and Unlocking the OSD · Adjusting OSD Settings Setting the Optimal Resolution The recommended resolution for this monitor is 1680 x 1050. To configure the monitor to this resolution, complete the setup procedure and make sure that the monitor is connected to the computer. The software download pages for your monitor will be displayed. Download and install the driver and software files using the instructions in the download pages. Using the Auto-Adjustment Function Press the auto button to optimize the screen performance for VGA (analog). Do not use this procedure if your monitor is using DVI input. If your monitor is using VGA (analog) input, auto-adjustment can correct the following image quality conditions: · · · · · Fuzzy or unclear focus Ghosting, streaking, or shadowing effects Faint vertical bars Thin, horizontal scrolling lines An off-center picture 16 Back to Contents Page Technical Support FAQs Technical Support FAQs (Frequently Asked Questions) Problem & Question Power LED is not on. Possible Solutions · Make sure the power button is on and the power cord is properly connected to a grounded power outlet and to the monitor. · In order for the Plug & Play feature of the monitor to work, you need a Plug & Play compatible computer and video card. · Check the monitor's video cable and make sure none of the pins are bent. · Make sure the HP monitor drivers are installed (HP monitor drivers are available at: http://www. hp. com/support) Picture is fuzzy and has ghosting shadowing problem. · Adjust the contrast and brightness controls. · Make sure you are not using an extension cable or switch box. We recommend plugging the monitor directly into the video card output connector on the back of your computer. · For VGA input, the auto-adjustment function may fix this problem. Picture bounces, flickers or wave pattern is present in the picture. · Move electrical devices that may cause electrical interference as far away from the monitor as possible. · Use the maximum refresh rate your monitor is capable of at the resolution you are using. Monitor is stuck in "Active Off-Mode". · The computer power switch should be in the on position. · The computer video card should be snugly seated in its slot. · Make sure the monitor's video cable is properly connected to the computer. · Inspect the monitor's video cable and make sure none of the pins are bent. · Make sure your computer is operational by hitting the Caps Lock key on the keyboard while observing the Caps Lock LED. [. . . ] *Notified body number (used only if applicable -- refer to the product label). 27 Disposal of Waste Equipment by Users in Private Households in the European Union This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product. Japanese Notice 28 Japanese Power Cord Notice Japanese Material Content Declaration A Japanese regulatory requirement, defined by Specification JIS C 0950, 2005, mandates that manufacturers provide Material Content Declarations for certain categories of electronic products offered for sale after July 1, 2006. [. . . ]